Werbung
Verfügbare Sprachen
Verfügbare Sprachen
CHARGING THE BATTERY PACK
•
Recharge only with the charger specified by the manufac-
turer. A charger that is suitable for one type of battery may
create a fire hazard when used with another battery pack.
NOTE: The battery pack is not fully charged when shipped from
the factory. Before using the device for the first time, you must
fully charge the battery pack to ensure its performance. The
battery pack should be removed from the gun during charging.
•
The lithium-ion battery pack can be charged at any time
without shortening its life. If charging stops suddenly, the
battery pack will not be damaged.
This battery pack is equipped with an "Electric Cell
•
Protection" (ECP) to prevent over-discharge.
When the battery pack is completely discharged, the
•
protection circuit switches the gun off.
•
Stop pressing the trigger when the gun shuts off automati-
cally. Otherwise, the battery pack may be damaged.
NOTE: The battery pack is equipped with the NTC temperature
monitor. Charging is only possible when the temperature is
between 0 and 45ºC.
Disposal
To remove the battery, press the
release button and pull the battery
backwards out of the gun.
Do not use excessive force during
this operation.
Respect the environment, and
recycle the spray gun, battery pack,
accessories and packaging.
Do not dispose of the spray gun and
battery pack in household waste.
Transportation
•
The lithium-ion battery packs supplied with the device
must be subject to dangerous goods regulations. Users
may transport the battery pack without additional
protective packaging.
•
However, for delivery to third parties (e.g., by air or freight
transport), special packaging and marking are required.
You should therefore consult your dangerous goods
expert regarding the delivery of dangerous goods.
•
Ensure that the battery pack is not damaged before
transport. Protect exposed terminals and pack the battery
pack to prevent shaking in the packing box.
•
If necessary, consider relevant national regulations.
MAINTENANCE
After using the filter for a period of time, you should check
whether it is dirty or not. If it is too dirty, you should replace the
filter by following the steps below:
1.Remove the battery pack and the filter
protector with a screwdriver.
2.Remove the dirty filter and replace it with a
new one.
3.Reinstall the filter guard.
TROUBLESHOOTING
Problem
Spraying with low flow or
without flow
Dripping of spraying
material
Poor spray atomisation
Spray fluctuation
Suspension phenomenon
of the spray material
Over spraying
Spray pattern too thin
· 10 ·
Cause
Solution
1.Clogged nozzle
1.Clean the nozzle
2.Clogged suction tube
2.Clean the suction tube
3.Flow regulator in low
3.Adjust the flow regulator
position
4.Tighten the suction pipe
4.Loose suction tube
5.Tighten the tank
5.Loose tank
6.Replace the filter
6.Clogged filter
1.Loose nozzle
1.Tighten the nozzle
2.Damaged nozzle
2.Replace the nozzle
3.Seal damaged nozzle
3.Replace the nozzle
4.Spray material
4.Clean the nozzle
accumulated on the
nozzle
1.High viscosity of the
1.Dilute the spray material
spraying material
2.Reduce the flow rate
2.High flow rate of
3.Adjust the flow regulator
spraying material
4.Clean the nozzle
3.Flow regulator in high
5.Replace the filter
position
6.Tighten the tank
4.Clogged nozzle
5.Clogged filter
6.Low pressure build-up in
the tank
1.Not enough spray
1.Refill the spraying
material in the tank
material
2.Clogged filter
2.Replace the filter
Spraying too much
Reduce the flow rate or
material
move the gun faster
1.Large distance between
1.Reduce the distance
spray gun and the surface
2.Reduce the flow rate
2.Large low rate of spray
material
Move the spray gun too
Increase the flow rate or
fast
move the gun more slowly
REF. 60043
Air
filter
aire
Werbung
