Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Anleitung_BG_BC_25_S_SPK7:_
GB
4. Intended use
The equipment is designed for cutting lawns and
grassed areas. The operating instructions as supplied
by the manufacturer must be kept and referred to in
order to ensure that the equipment is properly used
and maintained. Any use which is not expressly
permitted in the manual may result in damage to the
equipment and place the user in serious danger. Be
sure to observe the restrictions in the safety
instructions.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.
Important. Due to the high risk of bodily injury to the
user, the petrol power scythe must not be used to
carry out the following work: to clean dirt and debris
off walkways, or to chop up tree or hedge clippings.
Moreover, the petrol power scythe may not be used
to level out high areas such as molehills. For safety
reasons, the petrol power scythe may not be used as
a drive unit for other work tools or toolkits of any kind.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user/operator and not the manufacturer
will be liable for any damage or injuries of any kind
caused as a result of this.
5. Technical data
Engine type
2-stroke engine, air-cooled, chrome cylinder
Engine power (max.)
Displacement
Idle speed of engine
Max. engine speed
Max. torque
Scythe:
Trimmer:
Ignition
Drive
Weight (with empty tank)
Long handle length
Cutting line diameter
20
19.07.2010
8:35 Uhr
Seite 20
Cutting circle diameter of blade
Cutting line length
Cutting line diameter:
Tank capacity
Spark plug
Sound and vibration
Sound pressure level L
Uncertainty K
Sound power level L
Uncertainty K
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Idle speed
Vibration emission value a h = 4.01 m/s
K uncertainty = 1.5 m/s
Functions
Vibration emission value a h = 9.14 m/s
K uncertainty = 1.5 m/s
Reduce noise generation and vibration to a
minimum!
Use only equipment that is in perfect condition.
Maintain and clean the equipment regularly.
Adopt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
Wear gloves.
0.75 kW (1 HP)
6. Before starting the equipment
25 ccm
6.1 Assembly
-1
3,000 min
-1
10,500 min
6.1.1 Fitting the steady grip
Install the steady grip as shown in Figures 3a-3c. Do
not tighten the screws until you have set the perfect
-1
9,500 min
working position with the carrying strap. The steady
-1
8,000 min
grip should be aligned as shown in Figure 1. To
dismantle, proceed in reverse order.
Electronic
Centrifugal clutch
6.1.2 Fitting the long handle (Fig. 4a-4c)
6.2 kg
Slide the spacer sleeve (Fig. 4a / Item 23) between
the two screw holes (B). Insert the connecting screw
132 cm
(22) through the holes and the spacer sleeve as
43 cm
shown in Figure 4b. Screw the handle screw (Fig. 4b /
98.2 dB(A)
pA
pA
112 dB(A)
WA
WA
2
2
2
2
23 cm
4 m
2.5 mm
0.45 l
L8RTC
3 dB
3 dB
Werbung
