Dual CV 440 Bedienungsanleitung Seite 6

Controls
=
O V 4 D 9 Pè 63 PI =à
wb b nb b
BO De
-=
© a
17
18
19
21
BR
SRR
27
Phono button for record playback.
On/Off switch.
CD button for compact disc playback.
Tuner button for radio playback.
Tape 1 button for cassette or tape playback.
Monitor 1 button for tape control Tape 1.
Video/Tape 2 button for video or cassette playback.
Monitor 2 button for tape control Tape 2.
Control Display.
* Display for standby operation of the amplifier
(the output stages are switched off).
Cover. (Press lightly at the place marked with a triangle.)
Sound 1-4 buttons to store (in connection with Memo 20
button) and recall the stored tone adjustment. E
Volume- button for volume reduction (in 2-dB steps).
Volume + button for volume increase (in 2-dB steps)
(display in Control Display).
Phones Headphone jack for medium-range and high-impe-
dance stereo headphones with 6.35 mm jack plug.
Phono MM/MC Change-over switch from magnetic pick-up
(MM) to moving-coil pick-up (MC)
(display in Control Display 9).
Speaker A Selector button for loudspeaker pair A
(display in Control Display 9).
Speaker B Selector button for loudspeaker pair B
(display in Control Display 9).
Pre-Volume button for volume adjustment of the individual
inputs.
Memo button for storing of various tones. Adjustments in con-
nection with the Sound 1-4 (12) and Preset 27 buttons.
L Balance R for adjustment of the volume range ratio of the two
channels to the room conditions, for example, with asymmetric
positioning of loudspeakers (adjustable in 2-dB steps)
(display in Control Display).
-Bass + buttons for bass control (display in Control Display 9).
-Treble + buttons for treble control
(display in (Control Display 9).
Bass and treble controls adjustable for both channels together in
3-dB steps. In O position of the controls, the frequency response
is linear,
Caution: In the case of maximum bass or treble increase and too
high volume, the loudspeakers may be damaged.
Linear button for linear frequency response.
Muting button for muting of amplifier.
Loudness At low volume the bass and treble are boosted and
thus adapted to aural sensitivity.
Preset button for storing (in connection with Memo 20) and
recalling an certain volume and balance as well as tone adjust-
ment.
Connection Side
The connection jacks are set up symmetrically on the right side of the
back panel of the unit for the right channel (right channel) and on the
left side of the back panel for the left channel (left channel).
28 Speakers B Connection terminals for loudspeaker pair B.
29 Speakers A Connection terminals for loudspeaker pair A.
30 ett "o for selectable terminal capacity of the input Phono
39.
31 + Ground screw for record player.
32 Tuner Cinch (RCA) connection jacks for stereo tuner
(radio sets without output stage and loudspeakers)
(black or red = right channel, white = left channel).
33 Tape 1
Play/ Monitor Cinch (RCA) connection jacks to be connected to
output jacks (play, output) of the tape or cassette recorder.
34 Tape i
REC Connect cinch (RCA) connection jacks to input jacks (rec,
input) of tape or cassette recorder.
35 Tape 2/Video
"REC Connect cinch (RCA) connection jacks to input jacks (rec,
input), of tape or cassette recorder or of video recorder,
36 Tape 2/Video
Play/Monitor Connect cinch (RCA) connection jacks to output
Jacks (output, play) of tape or cassetter recorder or of video
recorder.
CD Cinch (RCA) connection jacks for CD player.
Phono
MC Cinch (RCA) connection jack for record player with moving-
coil pick-up cartridge.
39 Phono
MM Cinch (RCA) connection jack for record player with magnetic
pick-up cartridge.
40 Connection jack for the power cord supplied.
82
Connection of Program Sources
~ The connection jacks for the right channel are located, for all
program sources, on the right side of the rear panel of the unit, the
connection jacks for the left channel are on the left side of the rear
panel.
Record Players with Magnetic Pick-Ups
- Connect record players with magnetic pick-up cartridges to the
Phono MM 39 connection jacks
(black or red = right channel, white = left channel).
- Set Phono MM/MC 16 change-over switch to MM position. The
display MM appears in the display.
- The connection wire additionally provided is to be connected to one
of the two ground terminals + 31.