Installation Instructions; Installation Of Mae; Fitting The Drain Unit; Installation Of Maz - STIEBEL ELTRON MAE Bedienungsanleitung

2. Installation instructions

2.1 Regulations and Requirements
# This fitting must be installed, commissioned and maintained only by an approved specialist in accordance with these instructions.
# Area of application: open (pressureless) instantaneous water heaters.
# Building inspectorate test certificate PA ....
# Rated up to 0.6 MPa flow pressure - at pressures above 0.6 MPa, a pressure reducing valve must be fitted in the main pipe.
Rinse the cold water supply pipe thoroughly.

2.2 Installation of MAE

Insert the fitting with sealing ring (7) in the
washbasin and from below attach with U-
shaped washer (8), U-shaped thrust washer
(9) and clamping sleeve (10).
2.2.1 Water Connection
Connect the short connection hose marked
!
„blue" (4, blue ) to the angle valve - cold
water supply pipe.
Connect the two connection hoses to the
instantaneous water heater using union nuts
and seals.
Screw the connection hose (5,
the downward-pointing arrow to the inlet
connector of the instantaneous water heater,
!
and connection hose (6, red) with the
upward-pointing arrow to the outlet
connector.
When fitting the connection hoses, note the
following A :
– Do not bend hoses immediately after the
joint; leave a straight section of at least
15 mm;
– Do not kink hoses but ensure a minimum
curvature radius of 20 mm;
– Avoid distortion during fitting;
– Avoid tension during fitting;
– Twisting during fitting is not permitted.

2.3 Fitting the Drain Unit (11)

Unscrew the drain sleeve (11.1) from the
tundish (11.4) and from above push with the
seal (11.2) through the drain opening in the
washbasin and screw to the tundish applied
below the washbasin with the shaped seal
11.3 11.3
(11.3 11.3 11.3).
Insert the two-piece pull rod in the fitting
body, screw in place and connect to the drain
unit using the hinge piece.
Technical Data
Test pressure 1,6 MPa max.
0,3 MPa = ^ 3,5 l/min
Flow rate
Operating
temperature 90 °C max.
for the professional

2.4 Installation of MAZ

Insert the fitting with sealing ring (8) in the
washbasin and from below attach with U-
shaped washer (10), U-shaped thrust washer
(11) and clamping sleeve (12).
2.4.1 Water Connection
Connect the short connection hose marked
!
„blue" (5,
water supply pipe.
Connect the two connection hoses to the
instantaneous water heater using union nuts
and seals.
"
blue) with
Screw the connection hose (6,
the downward-pointing arrow to the inlet
connector of the instantaneous water heater,
and connection hose (7,
upward-pointing arrow to the outlet
connector.
When fitting the connection hoses, note the
A
following
– Do not bend hoses immediately after the
joint; leave a straight section of at least
15 mm;
– Do not kink hoses but ensure a minimum
curvature radius of 20 mm;
– Avoid distortion during fitting;
– Avoid tension during fitting;
– Twisting during fitting is not permitted.
Technical Data
Test pressure
Flow rate
Operating
temperature

3. Environment and recycling

Please help us to protect the environment by
disposing of the packaging in accordance with
the national regulations for waste processing.
4. Guarantree
For guarantees please refer to the respective
terms and conditions of supply for your
country.
blue ) to the angle valve - cold
"
blue) with
!
red) with the
:
1,6 MPa max.
0,3 MPa = ^ 3,5 l/min
90 °C max.

2.5 Installation of MAW

Screw the fitting with cover plate (5) into the
wall plate.
Screw the swivel outlet (4) to the fitting
body by turning the union nut.
Technical Data
Test pressure 1,6 MPa max.
0,3 MPa = ^ 3,5 l/min
Flow rate
Operating
temperature 90 °C max.
The installation, electrical connection
and first operation of this appliance
should be carried out by a qualified installer.
The company does not accept liability for
failure of any goods supplied which are not
installed in accordance with the
manufacturer's instructions.
9