Scheppach 7906100715 Originalbetriebsanleitung Seite 9

Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
Safety Information
m CAUTION
Read all the safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in and/or electric shock,
fire and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
Protect yourself and your environment from acci-
dents by taking the appropriate precautionary meas-
ures.
Do not use the stapler for a purpose for which it
•
is not designed.
Keep air tools safe from children.
•
Never use the equipment when you are not rested
•
or distracted.
• Connect the compressed air using a quicklock
coupling only.
Staplers may only be connected to lines/hoses
•
which do not allow the maximum permitted pres-
sure of the equipment to be exceeded by more
than 10%. A pressure regulator (pressure reducer)
with a downstream pressure control valve must be
fitted to the compressed air hose if the pressure
is higher.
The operating pressure must be adjusted by a
•
pressure reducer.
When using a pneumatically operated stapler/nail-
•
er, only use the pressure required for the specific
operation to prevent an unnecessarily high noise
level, excessive wear and consequential faults.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Never use oxygen or combustible gases as a pow-
•
er source. Danger of fire and explosion.
Always disconnect the equipment from the com-
•
pressed air source before tackling faults or starting
any maintenance work.
• Use only genuine spare parts. Repairs may only be
carried out by an authorized agent of the manufac-
turer or by an alternative specialist in accordance
with the specifications contained in the operating
instructions.
Wear the necessary protective clothing when
•
working with the stapler, in particular safety gog-
gles and protective gloves.
Do not exceed the maximum air pressure of 7.5
•
bar.
Do not direct the connected and loaded nailer at
•
other people.
Do not remove the earthing contact device.
•
• Never leave the equipment unattended when load-
ed.
Never use the equipment if defective.
•
Only use the types of staples/nails specified in the
•
technical data.
The equipment must always be depressurized af-
•
ter disconnection.
• Never use the equipment without staples/nails.
Never point an operational stapler directly at your-
•
self or at any other person.
Whilst working with the stapler, hold it in such a
•
way that your head and body cannot be injured in
case of kickback caused by disruption of the power
supply or by hard areas of the workpiece.
• Never trigger the stapler into the open air. This is
important to avoid the hazards of free-flying sta-
ples and of overloading the appliance.
For the purposes of transportation, the stapler
•
must be disconnected from the compressed-air
system, especially if you are using a ladder or are
adopting an unusual posture.
• In the workplace, carry the stapler only by its han-
dle and ensure that the trigger is inactivated.
Make allowance for the workplace conditions. Sta-
•
ples can potentially go straight through thin work-
pieces or they can slide off workpieces when working
on corners and edges, thus putting persons at risk.
• For you own personal safety, always use suitable
protective equipment such as, for example, hear-
ing and eye protection.
Check that the trigger catch functions correctly
•
every time before you use the equipment. You are
allowed to start using the equipment only if the de-
vice functions perfectly.
This equipment is not suitable for the following work:
If changing from one stapling point to another in-
•
volves moving about on platforms, steps, ladders
or any other structures similar to ladders such as,
e.g. roof battens.
• Sealing of boxes or crates.
Fitting of transportation braces, e.g. to vehicles
•
and wagons
9 І 56