Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Configuring the drive
Roller shutters
Awnings
Intermediate position
Intermediate position
of blind at any position
of blind at any position
between upper and lower
between upper and lower
end position
end position
Ventilation position
Fabric tautening
position
ventilation gaps open
Position is taut
Prerequisite for all actions: The channel of the hand-held transmitter is programmed in the receiver.
Defining the interim
Moving to the intermediate position
position in the receiver
Prerequisite: The intermediate position is defined.
Prerequisite: The blind is in
Press [DOWN/CLOSE ▼] button twice (in quick succession):
the upper end position.
1. Press the [DOWN/
Blind moves to the intermediate position saved.
CLOSE ▼] button until
If no intermediate position has been defined, the blind will
the desired intermediate
move to the lower end position.
Important: If you are using a venetian blind and a defined tilt
position is reached.
position (receiver in JA mode or „JA" in product name), the
2. Additionally press the
[STOP ■] button. The blind
venetian blind slats will also tilt.
If no tilt position has been defined, the blind will stop at the
will stop. The status LED
lights up briefly.
intermediate position with the slats closed.
The intermediate position is
If an intermediate position is to be approached for various
now stored.
receivers simultaneously, the receivers must be programmed
on one channel.
Defining one of the ventilation/fab-
ric tautening/tiling positions in the
receiver
Prerequisite: The blind is in the lower end
position.
1. Press the [UP ▲] button until the
ventilation gaps open, the venetian
blind slats are tilted or the awning
fabric is taut.
2. Additionally press the [STOP ■] button.
The blind will stop. The ventilation/fabric
tautening/tilting position has now been
saved.
General notes on troubleshooting
Fault
Receiver not responding and status
indicator of transmitter flashing orange
Receiver cannot be programmed
Receiver not responding and status
LED of transmitter flashing red
Receiver not responding and status
LED of transmitter not lighting up
Receiver reacting only intermittently
Empfänger fährt in die falsche Richtung
Venetian blind
Intermediate position
of blind at any position
between upper and lower end
position
Tilting position
Blind slats are tilted by brief
travel in the opposite direction
(only for receivers in JA mode
or with „JA" in product name)
Moving to one of the ventilation/tilting/
fabric tautening positions
Prerequisite: The ventilation/tilting/fabric
tautening position is defined.
Press the [OPEN ▲] button twice:
blind moves to the position saved.
If no ventilation/fabric tautening/tilting
position is defined, the blind will travel to
the upper end position.
Possible cause
Possible solution
Not transmitter programmed
Program the transmitter
Adapt the system configuration
Transmitter and receiver systems
are configured differently
(unidirectional or bidirectional)
1. No power supply
1. Check mains voltage.
2. The receiver is outside the radio
2. Change the transmitter's positi-
range.
on. Change the position of the
receiver's aerial.
3. Radio receiver defective
3. Replace receiver.
Battery in transmitter is used up
Replace batteries in transmitter
1. Poor radio reception
1. Change the transmitters's
position. Change the position of
the receiver's aerial.
2. Influence from faulty or non-
2. Localise the source of the inter-
approved radio systems
ference and rectify malfunction.
Directions are incorrectly pro-
Delete transmitter and program
grammed
correctly
Cleaning
Do not use solvent or abrasive detergents to clean the product.
Interio shading
Warranty
Within the legal warranty period, we will remedy any defects caused by
material or manufacturing defects by repairing or replacing the unit. Unau-
Intermediate position 1
thorised modifications will void the warranty.
of blind at any position
between upper and lower
end position
Reparatur
Intermediate position 2
Please specify the item number, item description, type of fault, situational
circumstances, presumed cause, unusual events prior to the problem.
any subsequent position
ob blind
Service / manufacturer's address
If malfunctions occur or the device is damaged despite correct handling,
Deleting the inter-
contact your contractor or dealer.
mediate position
elero GmbH
Press the but-
Antriebstechnik
tons [DOWN/
CLOSE ▼] +
[STOP ■] simul-
Conformity
taneously for ap-
prox. 3 seconds.
elero hereby declares that the COM series handheld transmitter is in
The intermediate
compliance with Directive 2014/53/EU.
position is now
The full text of the EU Declaration of Conformity is available at the following
deleted. The
Internet address: www.elero.com/downloads-service
status LED lights
up briefly.
Disposal
Batteries and old units may not be disposed of with household waste.
1. Dispose of packaging in the recycling bin for cardboard and paper.
2. Dispose of old batteries in the recycling bin for used batteries or have a
Deleting the ventilation/
retailer recycle them.
fabric tautening/tilting
3. Dispose of old units at an electronic waste recycling facility or have a
position
retailer recycle them.
Press the [OPEN ▲]
+ [STOP ■] buttons
Technical data
simultaneously and hold
them down for approx. 3
Power supply
seconds.
The ventilation/tilting/fab-
Battery life
ric tautening position has
Radio frequency [MHz] (Band)
now been deleted.
Transmitter power [mW] | [dBm]
Number of channels
Operating temperature [°C]
Relative humidity
Protection class (IP)
Dimensions (LxWxH) [mm]
modul transmitter
Weight [g] (incl. batteries)
Type of mounting (optional)
© elero GmbH
Maybachstr. 30
GERMANY
732378 Schlierbach
www.elero.de
3 V, 2 x Micro LR03 (AAA)
typical up to 2 years
868 | 915
≤ 500 | ≤ 10
1 resp. 6 (bidirectional in each case)
0 ... 50
0 ... 95 % non condensing
20
151 x 49 x 15
ca. 90
wall mounting
EN | 3
Werbung
