En Translation Of Original Instruction; Technical Data; De Übersetzung Der Originalanleitung - Neo Tools 99-059 Übersetzung Der Originalanleitung

TRANSLATION OF ORIGINAL INSTRUCTION
Single floodlight LED SMD 50 W 4000 lm on 1.8 m stand
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
• Make sure the electricity is switched off before installation.
• Please read all the following instructions before installing the unit.
• If the safety shield is damaged, it must be immediately replaced with
tempered glass.
• Do not use if cord is cut or damaged.
• Make sure the mains voltage in your location matches with the
voltage of the device.
• Any replacement or repair should be carried out by qualified person.
• Use only when ambient temperature is between – 25°C and 45°C.
• The device heats during operation. Do not mount directly on
flammable surfaces.
• The device should be placed at least 1 m from other objects.
• Do not open or dismantle the device by yourself.
SYMBOLS EXPLANATION
1 2
1. Read the manual.
2. Product conforms to EU directives.
3. Product conforms to EAC requirements
4. Product conforms to Ukraine's quality control system requirements
5. Ingress protection class IP65
FIGURES EXPLANATION
Fig. B.
1. Lamp body
2. Fixed nut
3. Locking nuts
4. Tripod
OPERATING
1. Spread the tripod's legs to the maximum position.
2. Lock legs' position using the locking knob (fig. B-4)
3. Unscrew the locks (fig. B-3) to slide the tubes to desired height. Screw
the locks to lock the stand in desired position.
4. Attach the lamp frame to the stand, securing it with a screw knob.
5. To adjust the floodlight angle, loosen the screws located on either side
of the bracket, until the desired angle is achieved, then re-tighten.
6. Connect the lamp to the power source.

TECHNICAL DATA

Single SMD floodlight
Parameter
Voltage
Power
Diode count
Diode type
Color temperature
Light flux
Ingress protection IP
Protection class
Mass
ENVIRONMENT PROTECTION
Do not dispose of electrically powered products with
household wastes, they should be utilized in proper
plants. Obtain information on waste utilization from
your seller or local authorities. Used up electric and
electronic equipment contains substances active in
natural
constitutes a potential risk for environment and
human health.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka
komandytowa with seat in Warsaw at ul. Pograniczna 2/4 (hereinafter
EN
99-059
3 4
Value
230V AC 50Hz
50 W
50
LED
6500K
4000 lm
IP65
I
3,56 kg
environment. Unrecycled
Grupa Topex) informs, that all copyrights to this instruction (hereinafter
Instruction), including, but not limited to, text, photographies, schemes,
drawings and layout of the instruction, belong to Grupa Topex exclusively
and are protected by laws accordingly to Copyright and Related Rights Act
of 4 February 2004 (ustawa o prawie autorskim i prawach pokrewnych,
Dz. U. 2006 No 90 item 631 with later ammendments). Copying,
processing, publishing, modifications for commercial purposes of the
entire Instruction or its parts without written permission of Grupa Topex
are strictly forbidden and may cause civil and legal liability.
EU Declaration of Conformity
Manufacturer: Grupa Topex Sp. Z o.o. Sp.k., Pograniczna 2/4 02-285
Warsaw
Product: Single reflector
Model: 99-060
Trade name: NEO TOOLS
Serial number: 00001 ÷ 99999
This declaration of conformity is issued under the sole responsibility of the
manufacturer.
The product described above complies with the following documents:
Low Voltage Directive 2014/35/EU
Electromagnetic Compatibility Directive 2014/30/EU
RoHS Directive 2011/65/EU as amended by Directive 2015/863/EU
Regulation (EU) 2019/2020 implementing Directive 2009/125/EC
Regulation (EU) 2019/2015
5
And meets the requirements of the following standards:
EN 60598-2-5:2015; EN 60598-1:2015+A1:2018; EN 62471:2008; EN
62493:2015; EN 62031:2008+A1:2013+A2:2015;
EN IEC 55015:2019; EN IEC 61000-3-2:2019; EN 61000-3-
3:2013+A1:2019; EN 61547:2009;
IEC 62321-3-1:2013; IEC 62321-5:2013 IEC 62321-4:2013+AMD1:2017
CSV;
IEC 62321-6:2015; IEC 62321-7-1:2015; IEC 62321-7-2:2017; IEC
62321-8:2017
This declaration refers only to the machinery in the state in which it was
placed on the market and does not cover components
added by the end-user or subsequent actions carried out by the end user.
Name and address of the person resident or established in the EU
authorised to prepare the technical documentation:
Signed on behalf of:
Grupa Topex Sp. Z o.o. Sp.k.
Hive. Borderland 2/4
02-285 Warsaw
Pawel Kowalski
Quality Representative of GRUPA TOPEX
Warsaw, 2022-02-01
Einzelner Fluter LED SMD 50 W 4000 lm auf 1,8 m Stativ
ACHTUNG:
VERWENDUNG DES ELEKTROWERKZEUGS SORGFÄLTIG DURCH
UND BEWAHREN SIE ES ZUM SPÄTEREN NACHSCHLAGEN AUF.
DETAILLIERTE SICHERHEITSVORSCHRIFTEN
• Vergewissern Sie sich vor der Installation, dass der Strom
abgeschaltet ist.
• Bitte lesen Sie vor der Installation des Geräts die folgenden
Anweisungen vollständig durch.
• Wenn der Schutzschild beschädigt ist, muss er sofort durch
gehärtetes Glas ersetzt werden.
• Nicht verwenden, wenn das Kabel durchgeschnitten oder
beschädigt ist.
• Stellen Sie sicher, dass die Netzspannung an Ihrem Standort mit der
equipment
Spannung des Geräts übereinstimmt.
• Jeder Austausch oder jede Reparatur sollte von einer qualifizierten
Person durchgeführt werden.
• Nur verwenden, wenn die Umgebungstemperatur zwischen - 25°C
und 45°C liegt.
4
DE
ÜBERSETZUNG DER ORIGINALANLEITUNG
99-059
LESEN SIE DIESES HANDBUCH VOR DER