Product Familiarisation; Intended Use; Operation - Silverline DIY 850W Plaster Mixer Handbuch

263965
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-related
hazards.
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool's operation. If damaged, have
the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
WARNING: When used in Australia or New Zealand, it is recommended that this tool is ALWAYS
supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.
Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Safety Information for
Mixing Machines
• This machine is designed for mixing water-based liquids with powdered building materials
including, but not limited to thinset, sealing and levelling compounds, cement, grout, textured
coatings, etc.
• With the correct accessory attached, this tool may be used to blend dispersion paints, varnish,
resins and other coatings
• This machine is NOT intended to be used with dusty compounds such as graphite, or with salt
solutions, corrosive agents or liquid manure
• This product does NOT satisfy food hygiene standards and is NOT to be used for preparing food
or as a kitchen appliance
• Always use the CORRECT mixing paddle or accessory for the material being mixed. Working
with an incorrect accessory might overload the tool and lead to spillage, insufficient blending
or personal injury
• Always inspect the power cord and connector before use. If you locate any damage, have the cord
replaced by a qualified electrician before attempting to use the machine
• Before use, check the accessories are safely installed
• NEVER use the machine in damp or wet locations. If the machine gets wet, ensure it is
disconnected from the power supply and ensures it dries COMPLETELY before further use
• ALWAYS position yourself securely, maintain sure-footing and operate the tool with BOTH hands
• DO NOT attempt to mount the tool on a stand or tripod. NEVER leave the machine running
unattended
• Unplug the machine from the mains power supply after EVERY use, to avoid accidental switch-on
850W Plaster Mixer 120mm
• Always route the power cord towards the rear of the operator, AWAY from the machine and work
area. Ensure that the cable does not present a tripping hazard for the operator and other people
in the vicinity
• If you are using this machine with an extension lead, always unwind the cable completely.
WARNING: This tool may ONLY be connected to power supplies that are protected by a RCD device.
Test the function of any RCD regularly.

Product Familiarisation

1. Mixing Paddle
2. Attachment Point
3. Output Drive
4. Handle Stand
5. On/Off Trigger Switch
6. Lock-On Button
7. Main Handle
8. Motor Vents
9. Front Handle
Accessories (not shown):
• 2 x spanners

Intended Use

Handheld electric paddle mixer used for the preparation of plaster, cement, levelling compounds,
emulsions and similar building and decorating materials.
Unpacking Your Tool
• Carefully unpack and inspect your new sander. Familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Attaching a mixing paddle
WARNING: Always disconnect from the power supply before attaching/changing accessories.
WARNING: Never fit any attachment with a maximum speed lower than the no load speed of the
machine.
• This plaster mixer is equipped with an M14 female Output Drive (3)
• M14 threaded mixing paddles are fitted by screwing them into the output drive. Tighten with
a suitable spanner
• Ensure that the mixing paddle is securely tightened before use

Operation

WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection, as well
as suitable gloves, when working with this tool.
Switching On and Off
WARNING: Always ensure that the power cord is not interfering with the mixing paddle or
presenting a tripping hazard for the operator or other personnel in the vicinity.
• Grip the mixer firmly by the Handles (7) and (9), with both hands
• To start the mixer, squeeze the On/Off Trigger Switch (5)
• Press the Lock-On Button (6) to lock the tool in the 'on' position
• To stop the mixer, squeeze the On/Off Trigger Switch and release
silverlinetools.com
5