Bosch GAS 35 L AFC Professional Originalbetriebsanleitung Seite 20

Wet/dry dust extractor
Dust class
Weight according to EPTA-Pro-
cedure 01:2014
Protection class
Protection rating
A) Measured using a vacuum hose 3 m long and 35 mm in diameter
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Automatic start/stop
Rated voltage Maximum power Minimum power
230 V 2200 W
Permitted connected load of the connected power tool.
These values can differ for other country-specific models. Please take
note of the information on the socket of the dust extractor.
Noise/Vibration Information
Noise emission values determined according to
EN 60335-2-69.
Typically the A-weighted sound pressure level of the dust ex-
tractor is 70 dB(A). Uncertainty K = 3 dB. The noise level
when working can exceed 80 dB(A).
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 60335-2-69: a
2
K = 1.5 m/s .
Assembly
Pull the plug out of the socket before cleaning or per-
u
forming maintenance on the vacuum cleaner, making
tool adjustments, changing accessories or putting
away the vacuum cleaner. This safety measure prevents
the vacuum cleaner from being started accidentally.
Fitting the holder for the vacuum hose (see
figure A)
– Slide the holder (5) for the vacuum hose firmly into the
corresponding adapters (30) from above until they click
into place.
Fitting the vacuum hose (see figure B)
– Attach the vacuum hose (21) to the hose adapter (2) and
turn it clockwise as far as it will go.
Note: The friction generated by the dust in the vacuum hose
and accessory during extraction causes an electrostatic
charge that the user may experience as static discharge (de-
pending on environmental factors and their physiological
state).
Bosch generally recommends using an anti-static vacuum
hose (accessory) to vacuum up fine dust and dry materials.
Bosch Power Tools
Fitting the vacuuming accessories (see figure C)
GAS 35 L AFC
The vacuum hose (21) is equipped with a clip system which
L
can be used to connect vacuuming accessories (dust extrac-
kg 12.2
tion adapter (20), curved nozzle (22)).
Fitting the dust extraction adapter
/I
– Push the dust extraction adapter (20) onto the vacuum
IPX4
hose (21) until you hear both snap fasteners (31) on the
vacuum hose engage.
– To remove the adapter, press the snap fasteners (31) in-
wards and pull apart the components.
Fitting the nozzles and tubes
– Push the curved nozzle (22) onto the vacuum hose (21)
until you hear both snap fasteners (31) on the vacuum
100 W
hose engage.
– Then attach the required extraction accessory (floor
nozzle, crevice nozzle, suction tube, etc.) firmly to the
curved nozzle (22).
– To remove the accessory, press the snap fasteners (31)
inwards and pull apart the components.
Inserting/removing the disposal bag or dust bag
(dry extraction) (see figures D1–D2)
For dry vacuuming, you can insert a disposal bag (23) or a
dust bag (accessory) into the container (1). This makes the
dust easier to dispose of.
2
<2.5 m/s ,
h
Note: If using a paper filter bag, you must make sure that
automatic filter cleaning (AFC) is switched off; you should
also do the same if using a fleece filter bag .
Inserting the disposal bag
– Open the catches (11) and remove the top part of the va-
cuum cleaner (10).
– Insert the disposal bag (23) into the container (1) with
the inlet facing forwards.
– Pull the inlet over the connection flange and all the way
into the recess of the connection flange.
– Make sure that the disposal bag (23) touches all the in-
side walls of the container (1).
– Fold the rest of the disposal bag (23) over the edge of the
container (1).
– Put the top part of the vacuum cleaner (10) on and close
the catches (11).
Removing and sealing the disposal bag
– Open the catches (11) and remove the top part of the va-
cuum cleaner (10).
– Pull the full disposal bag (23) backwards out of the con-
nection flange.
– Carefully take the disposal bag (23) out of the container
(1) without damaging it.
When doing so, make sure that the disposal bag does not
scrape against the connection flange or other sharp ob-
jects.
– Remove the adhesive strip cover and tape up the disposal
bag.
English | 19
1 609 92A 7MZ | (19.08.2022)