Seite 1
* Weights correspond to remote driver installation, with QPD connector for ECOBLAST 3-4, with Junction box for ECOBLAST 5-6. Attached driver means additional 7.1kg (15.7 lbs) for ECOBLAST 3-4, additional 7.5kg (16.5 lbs) for ECOBLAST 5-6 (including driver holder plates). Tolerance on weight values is +/-5%.
Seite 2
6.5kg 14,3lbs GEAR C - LAYOUT AND MOUNTING ECOBLAST 4-5-6 SAFETY CABLE ECOBLAST 3 600mm (23.6 in) - For installations over 3 meters of height: secondary safety system application is mandatory, which is appropriated for the luminaire load (for example steel safety...
Seite 3
CONNECT THE AC, CONTROL, LED REMOVE SCREWS MODULE WIRES MAKE THE ELECTRICAL CONNECTION TIGHTEN THE DRIVER COVER blade dimensions: 3.5 x 0.5 mm 3 Nm Use appropriate tool for electrical connections! 01-85-943 | DOC-0018707 rev J | 12-2021 www.schreder.com 3/12...
Seite 5
5G1.5mm (<100m) / 5G-AWG16 7G1.5mm (<100m) / 7G-AWG16 optical blocks 7G2.5mm (<200m) / 7G-AWG14 5G2.5mm (<200m) / 5G-AWG14 CONTROL CONTROL optical blocks optical blocks DRIVER CONNECTION ACCORDING TO PAGE 3-4-5 01-85-943 | DOC-0018707 rev J | 12-2021 www.schreder.com 5/12...
Seite 6
2: LED1 - block 10 Nm 3: LED2 + 4: LED2 - 10 Nm 10 Nm Remove screws from junction box cover Connect the junction box to the junction box support plate 01-85-943 | DOC-0018707 rev J | 12-2021 www.schreder.com 6/12...
Seite 7
LED3- 6 - Orange 6 - Six 6 - Orange 6 - Six LED3- Yellow/Green Green Green Yellow/Green Make the electrical connection with WAGO terminal blocks Tighten the junction box cover 01-85-943 | DOC-0018707 rev J | 12-2021 www.schreder.com 7/12...
Seite 8
F - ANGLE ADJUSTMENT STEPS ECOBLAST 3 Loosen the clamp screws (4xM8) 4 x M8 Adjust the tilting angle Tighten the clamp screws with 13Nm 13 Nm 4 x M8 13 Nm ANGLE LIMITATIONS max 70° max 70° 0° 0°...
Seite 9
Reassemble the 2 main clamps, 4 screws, nuts, washers and anti-rotation clips nuts, washers and anti-rotation clips to the from the initial position second position initial position second position second position initial position 01-85-943 | DOC-0018707 rev J | 12-2021 www.schreder.com 9/12...
Seite 10
In case of suspended mounting option, option,the angle of inclination can the angle of inclination could be between only between 60° and 70° 0-15° and between 40-70° without any collision without any collision 01-85-943 | DOC-0018707 rev J | 12-2021 www.schreder.com 10/12...
Seite 11
Half Value Inrush Current Data # Drivers For Each Circuit Breaker Time [µs] Type B Type C Type D Nominal I peak Half Value 6800 220/240 Time [µs] 1500 6800 220/240 1500 01-85-943 | DOC-0018707 rev J | 12-2021 www.schreder.com 11/12...
Seite 12
.يف حاله الحاجه لتغري االسالك الداخليه , يتم ذلك من خالل الرشكه املصنعه او الوكيل املخول لعمل ذلك او شخص مخول لذلك .دامئا افصل الدائره الكهربائيه قبل تركيب او صيانه الجهاز 01-85-943 | DOC-0018707 rev J | 12-2021 www.schreder.com 12/12...