Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OPERATING INSTRUCTIONS
ACCESSORIES
The Compound Mitre Saw is supplied with the following
accessories as standard:
•
Saw blade (fitted)
•
6mm hex wrench
•
side support table (x2)
•
Dust bag
•
Instruction manual
TRANSPORTATION
Lift the mitre saw only when the machine head is locked
in the down position, the saw is switched off and the
plug is removed from the power point.
Only lift the saw by the carring handle
castings. Do not lift the saw using the guards.
BENCH MOUNTING
The saw base has holes in each corner to facilitate bench
mounting.
1. Place the saw on a level, horizontal bench or work
table using bolts (not supplied) and fix the saw to the
bench using 4 bolts.
2. If desired, you can mount the saw to a piece of 1/2"
(13 mm) or thicker plywood which can then be clamped
to your work support or moved to other job sites and
re-clamped.
CAUTION. Make sure that the mounting surface is not
warped as an uneven surface can cause binding and
inaccurate sawing.
RELEASE KNOB
The release knob
(2)
is provided for holding the cutting
head down while transporting or storing the mitre saw.
The saw must never be used with the release knob
locking the head down.
MITRE TABLE LOCKS
The mitre table locks
(20)
the desired mitre angle.
The mitre saw cuts from 0° to 45° both left and right. To
adjust the mitre angle loosen the mitre table
press mitre
latch(21)
and rotate the mitre table to the
desired position.
The mitre table features positive click stops at 0°, 15°,
22.5°, 30° and 45° for quick setting of common mitre
angles.
BEVEL LOCK
The bevel lock
(10)
is used to set the blade at the desired
bevel angle. The mitre saw bevel cuts from 0° to 45° to
(29)
or outer
are used to lock the table at
locks(20)
the left. To adjust the bevel angle loosen the bevel lock
and adjust the machine head to the desired bevel angle.
SPINDLE LOCK BUTTON
The spindle lock button
saw from rotating. Depress and hold the spindle lock
button while installing, changing, or removing the blade.
ROTATING LOWER BLADE GUARD
The rotating lower blade guard
from both sides of the blade. It retracts over the upper
blade guard
(4)
as the saw is lowered into the workpiece.
TURNING ON AND OFF
1. To turn the saw on, moving the lock-off lever
left meanwhile depress and hold the on/off trigger
switch
(18)
.
2. To turn the saw off release the on/off trigger switch
(18).
ATTACH FENCE
For cutting safety, always use the attach
and do not modify it .
DUST EXTRACTION& DUST BAG
1. Fit the dust bag
(9)
to the dust extraction port .
2. A vacuum dust extraction device can be connected to
the dust extraction port. Use a suitable vacuum adaptor
if necessary. The dust extraction port has an internal
diameter of
35
mm.
SETTING THE TABLE SQUARE WITH THE BLADE
1. Make sure that the electrical plug is removed from the
power point.
2. Push the machine
head(1)
and engage the release knob
head in the transport position.
3. Loosen the mitre locks
latch(21)
.
4. Rotate the table
(15)
until the pointer is positioned at
0°
5. Release mitre
latch(21)
(20).
6. Loosen the bevel lock
0°bevel (the blade at 90°to the mitre table). Tighten
the bevel lock (10).
7. Place a set square against the table
part of the blade.
8. Rotate the blade by hand and check the blade-to-table
alignment at several points.
9. The edge of the set square and the saw blade should
be parallel.
10. If the saw blade angles away from the set square,
adjust as follows.
(22)
prevents the blade in the
(6)
provides protection
fence(13)
down to its lowest position
(2)
to hold the machine
(20)
and lifting up the mitre
and tighten the mitre locks
(10)
and set the machine head at
(15)
and the flat
(19)
to
Werbung
