CON-TEC TL-348 E-STOP Bedienungsanleitung Seite 5

User manual
E-bike rear light TL-348 E-STOP
1. Introduction
Congratulations on the purchase of your new device. The user's manual is part of this device and
contains important information to safety, installation and disposal. Familiarize yourself with all
operating and safety instructions before using the device. Use the device as described and in
the specified areas of application. Keep this manual in a safe place and have it with you when
using the device.
2. Used symbols
Products and packaging should be disposed of in an environmentally
friendly manner
Symbol for the detection of electrical and electronic equipment
USB - Universal Serial Bus - connection point for connection e.g. to a
computer (charging only)
K XXXX
Test mark of the Kraftfahrt-Bundesamt
Recycling code for disposal of cardboard
Mounting only on bicycles with pedal assistance with DC power supply
Product complies with the product-specific applicable European directives
3. Proper use
The product is intended for use on bicycles and serves the illumination of the road and as a tail
light. This LED front light and the LED tail light are approved according to the currently valid
RTLR (StVZO) as sole lighting on all bikes. The product is intended for outdoor use. Any other use
than described above or alteration of the product is not permitted and may cause damage to
the product. The manufacturer assumes no liability for damage arising from improper use. The
product is not intended for commercial use.
4. Safety information
- Do not look into the light.
- The rear light must be mounted and adjusted so that the reference axis is parallel to the
vehicle's median longitudinal plane and parallel to the road.
- The light distribution may be obscured by no other attached parts or pieces of luggage, not
even partially.
- The LEDs are not interchangeable. If the LED fails, the entire luminaire must be replaced.
Manual_TL-348 E-STOP
5. WARNING! LIFE AND ACCIDENT HAZARD FOR INFANTS AND CHILDREN!
Never leave children unattended with the packaging material, because of suffocation danger by
swallowing packaging parts. Always keep the device away from children. The device is not a toy!
This device can be used by children of age 8 and over and by persons with reduced physical
or mental capabilities or lack of experience and knowledge if they have been supervised or
instructed concerning the safe use of the device and by understanding resulting hazards.
Children are not allowed to play with the device. Cleaning and user maintenance should not be
carried out by children without supervision. Do not disassemble the device. Improper repairs can
cause significant risks for the user. Only have repairing made by qualified personnel.
6. Product illustration
1
2
3
4
5
7. Mapped components
rear light
1
each 2 outer LEDs, COB LEDs in the middle
2
integrated Z-reflector
3
mounting screws
4
Plug-in contacts for connection to the electr. System
5
8. Product assembly
Attach the rear light to the luggage rack. To do this, use the supplied bolts and nuts.
9. Product adjustment
Reference axis Reference axis
Attention!
Regularly check the correct setting and mounting height of your tail light. The tail light must be
mounted in an area of 250 to 1200mm above the roadway. It must be mounted and adjusted so
that the reference axis is parallel to the vehicle's median longitudinal plane and parallel to the
road surface (see pic.).
10. Connection to the electrical system of the bike
The sliding shoe (1) for connection to the electrical system is located on the back of the rear light
(5). Pull out the sliding shoe (5) until the two openings are congruent. Push the non-insulated
cable ends through the sliding shoe (5) according to the polarity into the contacts and slide the
sliding shoe (5) back again. As a result, the free cable ends are clamped.
black cable = current-carrying
black-white cable = ground
11.Operating
The rear light is switched on and off via the electr. system.
Brake light function explanation
The rear light is equipped with a brake light function. When the rear light is switched on,
it is initialized. The red LEDs of the rear light flashes during initialization and then lights up
continuously.
No settings are required and no „teach-in" is necessary. Due to the negative acceleration that
occurs during each braking process, an electronic switch activates the brake light function for
approx. 3 seconds. During this time all red LEDs shine brighter.
12. Cleaning
Clean the device only with a slightly damp, lint-free cloth. Never completely immerse the device
under water. Do not use any corrosive or abrasive cleaners. This causes damage to the device.