Werbung
Verfügbare Sprachen
Verfügbare Sprachen
. MEMORY STORAGE OF RADIO CONTROLS
A maximum of 250 codes, divided between chan-
nels 1 and 2 can be stored in the memory
1.
On the SLH master radio control, simultaneously press
and hold down push-buttons P1 and P2.
2.
The radio control LED begins to flash (for about 10
secs.).
3.
Release both push-buttons.
4.
Press, for 1 second, the push-button on the receiver
(Fig.1 ref.h) relating to the channel you wish to
associate with the radio control.
5.
The relevant LED on the receiver (Fig. 1 ref. g) begins
to flash slowly for 5 secs.
6.
Within these 5 secs., while the radio control LED is still
flashing, press and hold down the required push-but-
ton on the radio control (the radio control LED lights
up on steady beam).
7.
The LED on the board (Fig.1 ref.g) lights up on steady
beam for 1 second and then goes OFF, indicating that
storage was executed.
8.
RRelease the radio control push-button.
9.
Quickly press twice in succession the memory stored
radio control push-button.
The board will send a command to the output
associated with the channel.
10.
To add other radio controls, transfer the code of the
memory-stored push-button of the radio control to
the relevant push-button of the radio controls to be
added, observing the following procedure:
a–
On the memory stored radio control, simultaneously
press and hold down push-buttons P1 and P2.
b–
The radio control LED begins to flash.
c–
Release both push-buttons.
d–
Press the memory stored push-button and hold it
down (the radio control LED lights up on steady
beam).
e–
Bring the radio controls near, press and hold down
the push-button of the radio control to be ad-
ded, releasing it only after the double flash of
the radio control LED, which indicates learning
was executed.
f–
Quickly press twice the push-button of the new
memory stored radio control.
The board will send a command to the output
associated with the channel.
4. DELETION OF ALL RADIO CONTROLS
1.
To delete ALL the radio control codes associated with
channels 1 and 2, hold down push-button SW1 or SW2
(Fig.1 ref. h) for 10 seconds.
2.
The LED (Fig.1 ref. g) relating to the pressed push-
button flashes for the first 5 secs., and then flashes
more quickly for the next 5 secs.
3.
The LED lights up on steady beam for 2 secs and
then goes OFF.
4.
Release the pressed push-button when both the
relevant LED lights up on a steady beam.
This operation is NOT reversible.
5. FUNCTION LOGIC
You can command the receiver channels from
different radio controls. (E.g.: radio control 1
commands channel 1, radio control 2 comman-
ds channel 2)
PULSE FROM RADIO CONTROL
CHANNEL 1
OU-
PULSE
TPUT 1
OU-
/
TPUT 2
6. DESCRIPTION OF THE LABEL
a Name of producer
b Model identification code
c Identification number of the production batch
d Read the instructions
Observe the current regulations for a correct di-
e
sposal
f Notified body reference
CE DECLARATION OF CONFORMITY
Manufacturer: GENIUS S.p.A.
Address: Via Padre Elzi, 32 - 24050 - Grassobbio - Bergamo - Italia
Declares that: The radio system INTERMODO2 868
•
are in conformity with the requirements of directive
99/5/CE
•
and according to the requirements of the following
harmonised standards:
•
ETSI/EN 301 489-1 V. 1.8.1
•
ETSI/EN 301 489-3 V. 1.4.1
•
ETSI/EN 300 220 -2 V. 2.1.2
•
EN 60950-1:2006
•
EN 62311:2008
Grassobbio, 01 August 2008
5
CHANNEL 2
CHANNEL 2
dip switch
dip switch
1=OFF
1=ON
/
/
CONTACT
CLOSED UNTIL
PULSE
NEXT PULSE
FROM RADIO
CONTROL
Managing Director
D. Gianantoni
Werbung
