Rimage Professional 3400 Einrichtungs- Und Installationsanleitung Seite 2

6
Install the Everest 400 printer driver
The Everest 400 printer driver installs automatically.

 Note:If the New Hardware Wizard displays, follow the prompts to
complete the Wizard and install the Everest 400 printer driver.
7
Set up the Everest 400 printer
- 
Important! The ribbon carriers cannot be
removed from the printer unless the system is
powered on.


Note:For more detailed instructions on
replacing print and retransfer ribbons, refer
to the Rimage Professional 3400 and 5400N
User Guide.
a. Pull up on the printercoverlatch.
b. Lower the printercoverto expose the ribbon carriers.
c. Remove the RibbonCarriers.
i. Turn the centerlatch counterclockewise to unlock it.
ii. Pull the printribboncarrier orretransferribboncarrier to remove it
from the printer.
PrintRibbonCarrier
Unlocked
8
Install or replace the print ribbons
a. Lay theprintribboncarrieron
its back.
PrintRibbonCarrier
b. Remove theusedprintribbon (if needed).
i. Pull up on supplyrolland takeuproll.
ii. Remove the ribbon from the carrier.
2001541_B_EN
8
...Continued
c.
d. Lay the printribboncarrierback on its side.
e. Return the printribboncarrierto the printer.
f.
g.
9
Install or replace the retransfer ribbon
a.
b. On first use, remove thepackaging from the retransfer ribbon carrier.
RetransferRibbon
Carrier
CenterLatch
Locked
c.
d. Install the newretransferribbon.
SupplyRoll
TakeupRoll
e.
f.
Continued...
g.
Install thenewprintribbon.
TakeupRoll
i. With the supply roll on the right
side, and the takeup roll on the left
side, unroll a few inchesofribbon.
ii. Place the printribboncarrier on
top of the exposed ribbon.
iii. Place thesupplyroll on the carrier
and push down to snap it into place.
iv. Place thetakeuproll on the carrier and
push down to snap it into place.
Turn the centerlatch clockwise to secure it.
Close the printercover.
Remove the retransferribboncarrier from the autoloader.
i. Remove the tape
and plasticbrace
from the front of the
carrier.
ii. Remove tapeand
plasticpackaging Tapeand
PlasticBrace
from around the
outside of the
carrier.
Remove the usedretransferribbon
SupplyRoll
fromtheretransferribboncarrier (if
needed).
i. Pull up on the supplyrolland the 
takeuproll.
ii. Remove the ribbon from the
carrier.
i. With the supply roll on the left side, and the takeup roll on the
right side, unroll a fewinchesof
ribbon.
SupplyRoll
ii. Place theretransferribboncarrier
on top of the exposed ribbon.
iii. Place thesupplyroll on the carrier
and push down to snap it into
place.
iv. Place thetakeuprollon the
carrier and push down to snap it into place.
Return theretransferribboncarrierto the autoloader.
Turn thecenterlatchclockwise to secure the carrier.
Close theprintercover.
Copyright © 2010 Rimage Corporation
10
Test and verify
Use Rimage QuickDisc to run a 3-disc test job to verify that the system is
SupplyRoll
operating correctly. Refer to the Getting Started with Rimage Software
document available on the Rimage Professional 3400/5400N User Guide
disc.
11
Register the Rimage system
- 
Important!Make sure to register your system so that Rimage can notify
you of upgrades as they become available.
Product registration and warranty activation is available at
www.rimage.com/support/warranty-registration.
12
Learn more
Tapeand
Plastic
Packaging
• These documents are available on the RimageProfessional3400/5400N
UserGuideDisc that shipped with your autoloader:
Rimage Professional 3400 and 5400N User Guide
ƒ
Getting Started with Your Rimage Software
ƒ
Rimage Advanced Setup (Networking) Guide
ƒ
Diagnostic Test Instructions
ƒ
TakeupRoll
Access these documents by placing the UserGuidedisc in the disc drive
of a PC.

 Note: If the User Guide menu does not display automatically, select
Run from the Windows Start menu and browse to theHome.htm
file on the software disc.
• For information about submitting orders to the 3400 across a network,
or to view the latest information on remote accessing, refer to the
Rimage Advanced Setup (Networking) Guide.
TakeupRoll
• For information about operating and maintaining the 3400, refer to the
Rimage Professional 3400 and 5400N User Guide.
• For additional support and product information, go to
www.rimage.com/support.
Page 2