HIKMICRO SP Serie Kurzanleitung Seite 129

Battery
● The built-in battery cannot be dismantled.
Please contact the manufacture for repair if
necessary.
● DO NOT charge other battery types with the
supplied charger. Confirm there is no
flammable material within 2 m of the charger
during charging.
● For long-term storage of the battery, make sure
it is fully charged every half year to ensure the
battery quality. Otherwise, damage may occur.
● DO NOT place the battery near heating or fire
source. Avoid direct sunlight.
● DO NOT swallow the battery to avoid chemical
burns.
● DO NOT place the battery in the reach of
children.
● When the device is powered off and the RTC
battery is full, the time settings can be kept for
3 months.
● In the first use, power on the device and charge
the RTC battery with the lithium battery for
more than 2 hours.
● The battery voltage is 7.2 V, and the battery
capacity is 4800 mAh.
● The battery is certified by UL2054.
Maintenance
● If the product does not work properly, please
contact your dealer or the nearest service
center. We shall not assume any responsibility
for problems caused by unauthorized repair or
maintenance.
● A few device components (e.g., electrolytic
capacitor) require regular replacement. The
average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
● Wipe the device gently with a clean cloth and a
small quantity of ethanol, if necessary.
● Clean the lens with cotton wool and 99% ethyl
alcohol.
● If the equipment is used in a manner not
specified by the manufacturer, the protection
provided by the device may be impaired.
● Please notice that the current limit of USB 3.0
PowerShare port may vary with the PC brand,
which is likely to result in incompatibility issue.
Therefore it's advised to use regular USB 3.0 or
USB 2.0 port if the USB device fails to be
recognized by PC via USB 3.0 PowerShare port.
● Your camera will periodically perform a self-
calibration to optimize image quality and
measurement accuracy. In this process the
image will pause briefly and you'll hear a "click"
as a shutter moves in front of the detector. The
self-calibration will be more frequent during
start up or in very cold or hot environments.
This is a normal part of operation to ensure
optimum performance for your camera.
Using Environment
● DO NOT expose the device to extremely hot,
cold, dusty, corrosive, saline-alkali, or damp
environments. Make sure the running
environment meets the requirement of the
device. The operating temperature shall be -
20 °C to 50 °C (-4 °F to 122 °F), and the
operating humidity shall be 95% or less.
● Place the device in a dry and well-ventilated
environment.
● DO NOT expose the device to high
electromagnetic radiation or dusty
environments.
● DO NOT aim the lens at the sun or any other
bright light.
● When any laser equipment is in use, make sure
that the device lens is not exposed to the laser
beam, or it may burn out.
● The device is suitable for indoor and outdoor
uses, but do not expose it in wet conditions.
● The level of protection is IP 54.
● The pollution degree is 2.
Calibration Service
We recommend you send the device back for
calibration once a year, and please contact the
local dealer for the information on maintenance
points. For more detailed calibration services,
please visit
https://www.hikmicrotech.com/en/support/calibr
ation-service.html.
Technical Support
● The
https://www.hikmicrotech.com/en/contact-
us.html portal will help you as a HIKMICRO
customer to get the most out of your HIKMICRO
products. The portal gives you access to our
support team, software and documentation,
service contacts, etc.
Emergency
● If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the
power cable, and contact the service center.
127