Bosch GDS 18 V-LI HT Professional Originalbetriebsanleitung Seite 13

Technical data
Cordless impact screw-
driver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard
screwdriving application ac-
cording to ISO 5393
Machine screw diameter
Tool holder
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
B)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
C) only for inductive batteries
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-2.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 96 dB(A); sound power level
107 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to
EN 62841-2-2:
Impact tightening of fasteners of the maximum capacity of
the tool:
2 2
a = 12.5 m/s , K = 3.4 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
Bosch Power Tools
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
GDS 18 V-LI HT
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
3 601 JB1 3..
not actually being used should also be taken into account.
V = 18
This may significantly reduce vibration and noise emissions
rpm 0–1.900
over the total working period.
rpm 0–2.100
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
Nm 650
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
mm M 12–M 20
Assembly
∎ ½"
A) Remove the battery from the power tool before carry-
kg 2.7-3.2 u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
°C 0 to +45
from unintentionally pressing the on/off switch.
°C –20 to +50
Battery charging
GBA 18V.. Note: The battery is supplied partially charged. To ensure
GBA 18V... W
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
C)
GAL 18...W
The lithium-ion battery can be charged at any time without
GAL 18V-..
reducing its service life. Interrupting the charging process
GAX 18V-30
does not damage the battery.
AL 1820 CV
AL 1860 CV
The lithium-ion battery is protected against deep discharge
GAL 1880 CV by the "Electronic Cell Protection (ECP)". When the battery
GAL 3680 CV is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Battery Charge Indicator
The three green LEDs of the battery charge indicator indic-
ate the state of charge of the battery (3). For safety reasons,
it is only possible to check the state of charge when the
power tool is not in operation.
Press the button for the battery charge indicator to show the
state of charge. This is also possible when the battery (3) is
removed.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 3 x green
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Removing the battery
The battery (3) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (4)unintentionally. As long as the battery is in-
English | 13
Capacity
≥ 2/3
≥ 1/3
< 1/3
Reserve
1 609 92A 4PS | (24.10.2018)