AVANCIS PowerMax SMART Installationsanleitung Seite 11

Vorschau ausblenden

Seite von 40

/ 40
Lesezeichen

Verfügbare Sprachen

AVANCIS POWERMAX

PHOTOVOLTAIC MODULES

SAFETY, INSTALLATION AND OPERATION MANUAL

General Information

• Before starting to handle, install and

oper ate PowerMax

modules, all safety,

instal lation and operation instructions

should be understood. Follow all appli-

cable local, regional, national and inter-

national regulations, code requirements

and standards.

• Keep unauthorised people away from

the PV system and the PV components

when unpacking and installing.

• PowerMax

modules produce voltage

when exposed to light, even when

oper ated in open-circuit mode.

• PowerMax

modules produce approxi -

mately full voltage as specified on the

mod ule label, even under low-light

conditions. With light intensity, both

current and power will increase.

• Under operating conditions, a Power-

Max

module is likely to produce more

current and/or voltage than reported at

Standard Test Conditions (1,000 W/m²

irradiance in the plane of module, mod-

ule temperature 25 °C and a spectral

distribution of irradi ance according to

air mass [AM] 1.5). Accordingly, the val-

ues of short-circuit current (I

open-circuit voltage (V

) given on the

module label should be multiplied by a

factor of 1.25 when determining com-

ponent voltage ratings, conductor cur-

rent rating, fuse sizes and the size of

controls connected to the PV output.

• Ensure that PowerMax

modules are

only subjected to ambient temperatures

in the range of -40 °C to +80 °C.

• Artificially concentrated light must not

be directed on PowerMax

modules.

• PowerMax

modules must not be used

on any kind of moving vehicles.

• Installations where PowerMax

ules come into contact with salt, salt

water or salt water spray exceeding IEC

61701:1995 (salt mist corrosion test)

values, are excluded from application.

• PowerMax

modules must not become

partially or wholly submerged in water

or be exposed to water spray (e.g. foun-

tains).

• PowerMax

modules should not be lo-

cated near aggressive substances, such

as salt (see above) or any other types of

corrosive agent, which could harm the

module.

• In case the PowerMax

modules are

used in building-integrated PV systems,

follow all applicable regulations, includ-

ing local building codes.

• Do not disassemble, modify or adapt

PowerMax

modules and their serial

numbers or remove labels.

• AVANCIS recommends keeping a

record of the PowerMax

module serial

numbers associated with the exact lo-

cation in the PV system.

• Customer and installer should save

this document.

Handling Safety

• Please follow the instructions on the

AVANCIS module box.

• The module boxes are not weather-resis-

tant. Removing the PowerMax

from the box is easier starting at the box

side with the module which is placed

higher.

• The EPS parts used for packaging are marked

with the EPS-Recycling symbol. For recycling

of EPS parts in your region, please visit

www.epsrecycling.org/pages/home.html.

• Do not stand or step on the module

boxes or on the PowerMax

and prevent objects from falling on the

modules.

• Do not drop PowerMax

avoid setting the module down hard on

any surface, particularly when placing it

on a module corner.

• Do not damage or scratch the Power-

Max

module surfaces.

• Do not use the junction boxes, electrical

cables or connectors as a grip to handle

the PowerMax

modules.

• Never leave a PowerMax

supported or unsecured, and prevent

) and

modules from sliding down any sur-

faces. On a sloped roof for example this

could be done by fixing two M6 or si -

milar size stainless steel bolts, with nuts

and lock washers in the pre-drilled

mounting holes on the backside of the

coated steel back rails. Make sure that

the additional steel parts will never hit the

support structure once the PowerMax

module is installed.

• Do not apply paint, glue or adhesive to

the surface of the PowerMax

• A PowerMax

module with broken glass

or a damaged back rail or other parts

mod-

cannot be repaired and must not be used.

This module could have sharp edges

and cause injury. Broken or damaged

PowerMax

modules must be handled

carefully and disposed of properly.

Installation Safety

• Do not install when there are adverse

conditions, like strong or gusty winds or

frost ed roof surfaces. Also do not work

modules

under wet conditions, and use dry tools

only.

• Use only insulated tools that are ap-

proved for working on electrical instal-

lations.

• AVANCIS recommends to use protective

clothing, such as appropiate gloves for

protection against electrical shock and

sharp parts.

modules

• Follow appropriate safety requirements

when installing PowerMax

heights to avoid possible falling or any

modules, and

other safety hazards.

• Make sure that the cables and connec-

tors are positioned between the glass

and back rails (if possible). In this way

damage to the cable by the back rail

edge can be avoided.

• Securely fasten the electrical cables after

connection, for example by using the

extra pre-drilled hole in the back rails,

module un-

but avoid any excessive mechanical stress

on them.

• Electrical cables should be mounted in

such a way that they do not cause peo-

ple to trip or stumble.

• PowerMax

switched off by removing them from

light or by fully covering their front sur-

face with an opaque material. When

working with PowerMax

light, follow all applicable regulations

regarding working with live electrical

equipment.

module.

• Do not touch electrical terminals or bro-

ken electrical cables or ends of wire

while the PowerMax

posed to light or while installing the

module. Contact with electrically active

parts or any surface of broken Power-

Max

modules can result in burns,

sparks and lethal shock.

• Ensure that connectors are clean and

dry before connecting them and that

they are not submerged in water, snow

or ice during operation.

• Never disconnect electrical connections

or unplug connectors under load, in

order to prevent direct current to arc

across gaps or any other dangers.

• Do not wear metallic jewellery while

performing installation.

• Cable conduits should be used in loca-

tions where wiring is accessible to chil-

dren or cable damaging animals, such

as marten, etc.

• Make sure that the installation of the PV

system does not cause corrosion of the

system itself or parts near the system.

modules at

modules can only be

modules in

module is ex-

AVANCIS PowerMax SMART Installationsanleitung Seite 11

Verfügbare Sprachen

Verwandte Produkte für AVANCIS PowerMax SMART