Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Instruction Manual
(Site 2 / 2)
Time switch (with Astro function)
12. Cycle**
Program -> New program -> Channel A/B/C/D -> Cycle 1 - 4 -> ...
For the cycle function it is possibile to enter a periodic switching time. The time switch acts as a recycling timer and switches between pulse (ON) and pause (OFF). The
max. value for pulse and pause is 9:59:59 h:mm:ss.
The cycle is not offered in the menu
New program
cycles within submenu
of menu
Cycle
Options
After having defined and activated the cycle (point 13) please proceed with following programming instructions:
Switch to main menu / Enter-mode and using the
Confirm sub-menu
by pressing
New program
By using the
-buttons select the desired channel for switching and confirm by pressing
Pick the appropriate cycle using the
-buttons and confirm by pressing
Using the
-buttons select which day or days of the week the cycle will be activated by selecting „
Set the start time of the Cycle: Hours
then confirm by pressing
Verify the entered switching time: If the flashing summary of the programming step is correct, confirm this by pressing
between
and
which you select by pressing
edit/delete
end
If you want to continue programming, confirm
next switching
To leave the programming menu select
.
end
The selected cycle is terminated (over-ridden) by a standard switching time (
14. Astro-function*
Program -> new program -> channel A/or B -> ...
The astro function allows you to switch the whole year through in relation to sunset and sunrise, e.g. for illumination purposes (
with sunset and
with sunrise). The programming is made according to (8 / 9) with following difference:
ON
astro-OFF
Choose astro function
and
astro ON
astro OFF
While programming an astro program step there will be no time (hh:ss) suggested (8H / 9H). Instead of this you have the possibility to
enter an
. E.g. if you like to switch on the light 20 minutes before sunset would you enter an
offset
while programming
.
astro ON
16. External Input ***
Options -> Input-> ...
The external input can be connected to a switched contact such as a push-button or light switch. Therefore you can activate and de-activate functions from a remote
location or automatically from a control system
For 35mm-devices: The external input is only featured on the one channel version.
To connect an external switch or push-button: Phase L 230V~
The resulting operation of the output channel, depending on the status of the external input is defined within menu
Functional options of the „external input":
Within menu
and submenu
you have to define if a switch or a push-button-signal will be applied to the external input. Furthermore you can choose the
Options
Input
channel(s) which react to the external signal:
Using the
-buttons select if you are connecting a
Select the channel(s) which will be controlled by the external signal with the
be controlled by the external signal remain deactivated, confirm
Define a response function within menu
Options
input is activated!
The pre-defined (default) setting is the standard '
17. Channel keys
Options -> channel-keys -> ...
Within the
menu you will find submenu
Options
opportunity to assign different response functions to the output channels.
These response functions will only be carried out when using the channel-keys
switch (manual over-ride) or optionally when activating the channel with the external input. Thus,
a programmed switching time will be executed as usual, independent of the settings within this
channel-key-menu.
The correlation between the channel-keys and the channels is as follows:
channel A => channel key A (push-button "A" of the device)
channel B => channel key B (push-button "B" of the device)
...
18. Switchoff warning
Options -> Switchoff warning -> ...
Within menu
and submenu
Options
Switchoff warning
: The function remains inactive.
Warning No
: The function is activated and the switch off is signalled in advance (For illumination purposes the warning is signalled by the flashing of the light
Warning Yes
according DIN 18015-2 = warning to avoid sudden darkness).
An activated warning affects all channels and all OFF switching times
19. Additional adjustments
Menu
Main menu
Application
Program
To query the programming steps and remaining memory locations
Program query
Copy from one channel to another. Memory of the channel won't be
overwritten; the copied switching steps appear additionally.
Program
Program copy
Permanent by date function is not copied!
!
Deletion of switching time(s). The program for all channels, single
Program
channels and single programming steps within on channel can be
Program delete
deleted.
Adjustment of date and time
Adjustment
Date-Time
Adjustment of the daylight saving time mode (ON/OFF)
Adjustment
Summertime
Adjustment
Choice of languages
Language
Reset to the state of delivery.
Adjustment
Factory Defaults
Date, time and switching program will be lost!
!
Displays the hour counter and pulse counter for each channel and
Options
Counter
the time switch itself.
The time switch can be locked with a 4-digit PIN-Code. The code
can be adjusted, activated and deactivated. If you have forgotten
Options
PIN-Code
the Code please call customer service.
Press all front keys for 2 seconds. The time switch is reset. The values for date and
Reset-Function
time will be deleted and have to be re-entered. The switching program has not
been deleted!
*Within astro time switches
**Within standard (non-astro) time switches
***One-channel version
GB
if you haven't defined and activated a cycle. Once you have activated and defined at least one of the 4 different
(point 13), a switching time with cycle function is programmable.
-buttons choose the
-menu then confirm by pressing
Program
.
.
.
. Minutes
then confirm by pressing
by pressing
.
,
,
ON
OFF
Pulse
respectively (9F).
or a
and confirm by pressing
pushbutton
switch
buttons (
channel ... yes)
then press
to confirm
channel ... no
and submenu
(point 17). This function will be performed by the output channel when the external
Channel-keys
which changes the switching status from
Change function'
Overview „channel-keys" functions:
. Here you have the
If you have assigned a specific response function to a channel, this switching function will occur if you push the channel-button on the front plate of the time
channel-keys
switch (or if the external input for this channel is activated and a signal is applied to the input, as explained under point 16). For each channel one out of the
following functions can be defined:
of the time
the early warning switch off function can be activated and deactivated:
.
or „
, then confirm each day by pressing
Yes"
No"
.
. After confirmation you have the choice
) or the subsequent switching time of another cycle.`
15. Astro-adjustments*
Adjustment -> Astro -> ...
The following options concerning the astro function are adjustable to satisfy your needs:
astro-
Position location:
cities.
Position coordinates:
of minus 20 minutes
offset
Block Sunrise:
Block Sunset:
than 10 p.m. even if sunset is later.
and submenu
Options
Channel-keys
.
and confirm by pressing
. Channels which should not
to
and vice versa.
ON
OFF
(default setting)
By pressing the channel key (or optionally using the external input) the switching status changes from
Change function
:
to
. This corresponds to a standard manual over-ride of the channel.
OFF
ON
By pressing the channel key (or optionally using the external input) the Timer starts and the corresponding channel switches
Timer function:
the expiry of the Timer-time the channel switches
OFF
After pressing the channel-button = Timer stops and the channel switches
Signal on the external input = Timer restarts/ Staircase lighting timer -> Resettable.
By pressing the channel key (or optionally using the external input) the cycle function starts. Attention: This function is only available if
Cycle 1 – 4:
the cycle is activated and defined in advance within menu
By pressing the channel key (or optionally using the external input) the channel switches permanently
Perm on:
channel key of the device is pressed again.
By pressing the channel key (or optionally using the external input) the channel switches permanently
Perm off:
channel key of the device is pressed again.
The Change function, Timer function and Cycle functions will be overridden by the regular switching program or by a manual over-ride!!!
20. Program modify
Program -> Program modify -> ...
Within
each single switching time can be modified.
Program modify
21. Data-key
With a Data-key following activities are possible:
: Writes the data from the time switch into the memory of the Data-key.
Save data
: Writes the data located inside the Key into the memory.
Program timeswitch
: The time switch will solely apply programming steps from the Data-key. The
Key function
switching program of the time switch is suppressed.
: To query the switching program of the Data-key.
Key readout
müller SC 28.X2 pro / SC 28.X4 pro
13. Cycle options**
Options -> Cycle -> Cycle 1 - 4 -> ...
You have the possibility to define 4 different Cycles. For these purposes choose menu
and sub-menu
Options
Cycle
deactivated (the max. value for pulse or pause is 9:59:59 h:mm:ss):
Choose menu
and sub-menu
Options
Select with
-buttons one out of the 4 cycles (
confirm with
.
Activate the cycle by changing
confirming with
.
Define duration of the pulse
„on-time"
Define duration of the pause
.
„off time"
Confirm
with
.
End
The cycle is now offered within the programming menu.
Further applications of the cycle function in combination with: External Input
function (16) and/or Channel keys function (17)
Adjust your geographical position with pre-defined choice of regions/countries and
Adjust your geographical position with longitude, latitude and time zone.
Earliest possible point in time for the astro function (sunrise).
Latest possible point in time for the astro function (sunset), e.g. switching on the light not later
. If the channel receives another signal before the expiry of time the time switch reacts as follows:
OFF.
and submenu
. Astro time-switches do not have the cycle feature!!!
Options
Cycle
paladin 172 4X2 pro / 172 4X4 pro
. The different cycles can be acivated, defined or
and confirm with
.
Cycle
) and
Cycle 1 – Cycle 4
to
with
-buttons and subsequent
No
Yes
(
->
...).
(
->
...).
to
ON
OFF
. After
ON
. This status remains active until the
ON
. This status remains active until the
OFF
BA SC28X2_SC28X4pro MP; DE, GB - 22426 – 2008.03-01
or
Werbung
