Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1.
Safety instructions:
For skilled electricians and trained
personnel in accordance with national
legislation, including the relevant
standards and, where applicable, in acc.
with IEC/EN 60079-14 on electrical
apparatus for explosive atmospheres.
– The light fitting is not suitable for use in
hazardous areas of zone 0, 1 and
zone 20, 21!
– The requirements of the IEC/EN 60079-31
regarding excessive dust deposits and
temperature to be considered from the
user.
– The technical data indicated on the light
fitting are to be observed!
– Disconnect equipment before opening!
– Avoid powering up repeatedly for short
periods of time.
– Changes of the design and modifications
to the light fitting are not permitted!
– The light fitting shall be operated as
intended and in undamaged and perfect
condition!
– Repairs may only be carried out by CCH/
CEAG or a qualified "electrician"!
– Do not keep these operating instructions
inside the light fitting during operation!
Observe the national safety rules and
regulations for prevention of accidents
and the following safety instructions
which are marked with an (
operating instructions!
6
Explosion protected light fittings
Series: nLLK 10
2.
Technical data
Light fittings with G5 bi-pin cap
nLLK 10 14/14
nLLK 10 28/28
nLLK 10 35/35
EC-Declaration of conf.
Marking accd.2014/34/EU and directive
Gas
Dust
Rated voltage
Rated frequenzy
Lamps to be fitted
Fluorescent lamps T5/ Ø16 mm
14 W HE
28 W HE
35 W HE
Protection acc. to EN/IEC 60529
Insulation class to EN/IEC 61140
max. permissible ambient temperature
nLLK 10 14/14
nLLK 10 28/28
nLLK 10 35/35
with through-wiring
nLLK 10 14/14
nLLK 10 28/28
nLLK 10 35/35
Storage temperature in original packing
Supply terminal clamping capacity
2x per screw-terminal
min.
max.
Conductor cross-section with through-wiring
) in these
Cable entries moulded plastics
suitable cables and test torques of the
pressure srew
seel 1+2
1
seel 2
1
2
Test torque for screw in thread cable entry
Metal thread
For permanently laid cables only
Dimensions of light fittings and for mounting
Weight
nLLK 10 14/14
nLLK 10 28/28
nLLK 10 35/35
(1)
Intensive sun radiation in areas of high ambient temperatures may cause inadmissible temperature rise inside
of the luminaire. This may result a decrease in lifetime of the electronic ballast (EVG). Therefore those luminaires
should be switched off during daytime by a photocell control.
(2)
The tests of clamping ranges and torque values were performed with metal mandrel.
The clamping range can vary by using cables with different manufacturing tolerances and material properties.
Please use the combination of sealing 1 + 2 for the intermediate region.
(3)
When selecting the seal rubber, ensure that the pressure screw can be tightened when carrying out any future
maintenance work on the cable entry.
(1)
min.
2
(2)(3)
max.
min.
(3)
max.
2 x 14 W HE
2 x 28 W HE
2 x 35 W HE
BVS 10 ATEX E 149
D II 3 G Ex nA de IIC T4 Gc
D II 3 D Ex tc IIIC T80°C Dc IP66
220 V - 240 V AC
220 V - 240 V DC
50 - 60 Hz
IEC 60081
IEC 60081
IEC 60081
IP 66
I
-25 °C to +50 °C
-25 °C to +50 °C
-25 °C to +45 °C
-25 °C to +45 °C
-25 °C to +45 °C
-25 °C to +40 °C
-25 °C to +50 °C
single-wire
multi-wire
1.5 mm
2
1.5 mm
6.0 mm
6.0 mm
2
2.5 mm
for max. 16 A
2
M25 x 1.5
Ø cable (mm)
Pressure screw (Nm)
10.0
2.3
13.0
2.6
13.5
1.5
15.0
2.3
3,0 Nm
M20 x 1.5
see fig. 2
approx. 4.0 kg
approx. 6.0 kg
approx. 7 .3 kg
GB
2
2
Werbung
