Herunterladen Inhalt Inhalt Diese Seite drucken

RND lab RND 560-00264 Bedienungsanleitung

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

LCD Touchscreen
Soldering Station
User Manual
RND 560-00264
CAUTION: Read the instructions before using the machine
www.rnd-electronics.com

Werbung

Inhaltsverzeichnis
loading

Inhaltszusammenfassung für RND lab RND 560-00264

  • Seite 1 LCD Touchscreen Soldering Station User Manual RND 560-00264 www.rnd-electronics.com CAUTION: Read the instructions before using the machine...
  • Seite 2 Boot Features First insert the power cord connector into the power cord connector at the back of the machine, and then • Suitable for lead free soldering applications insert the power cord plug into the power socket. Turn on the power switch on the back of the machine: •...
  • Seite 3 The setting method is as follows: MODEL RND 560-00264 To select the function you want to set, first press the function selection key at the bottom of the display screen to select SOLDER or DESOLDER. After the selection is completed, the function indication key will point to the function you selected.
  • Seite 4: Spare Parts

    Spare parts PROCEDURE FOR CLEANING CLOGGED TIPS Caution: Soldering iron This procedure is to be working in high temperature. Be careful to avoid burning your fingers during this operation: • Be sure that the spring wire (included) will not go through the nozzle of the desolder tip. •...
  • Seite 5 3. Point the collector down while shaking slightly (see Figure 12.) and the waste solder will fall out. This task must be carried out periodically for proper operation of the station. FIG-8 FIG-9 4. Remove again and shake out any loose melted solder in the tip per Figure 9, the tip should now be FIG-12 unclogged.
  • Seite 6: In Line Filters

    Tip chart INTERCHANGEABLE TIPS FOR RND 560-00264 FIG-17 FIG-18 Soldering tips 5. Remove old cotton filter and replace (see Figures 17 & 18). RND 560-00250 IN LINE FILTERS: RND 560-00251 1. Unscrew in line filter (see Figure 19) and then pull apart (Figure 20).
  • Seite 7: Lötstation Mit Lcd-Touchscreen

    Lötstation mit LCD-Touchscreen Benutzerhandbuch RND 560-00264 www.rnd-electronics.com ACHTUNG: Lesen s ie diese anleitung, bevor Sie das gerät benutzen...
  • Seite 8: Leistungsmerkmale

    Inbetriebnahmet Leistungsmerkmale Verbinden Sie zuerst das Netzkabel mit dem Netzanschluss auf der Rückseite des Gerätes und stecken Sie anschließend den Stecker des Netzkabels in die Netzsteckdose. Schalten Sie den Netzschalter auf der • Geeignet für bleifreies Löten Rückseite des Geräts ein: •...
  • Seite 9: Funktion Der Temperatureinstellung

    3 Temperatureinstellungen CH1 bis CH3. Vorgehensweise: MODELL RND 560-00264 Um die einzustellende Funktion zu wählen, drücken Sie zuerst die Funktionsanzeigetaste am unteren Rand des Displays, um LÖTTEN oder LÖSCHEN auszuwählen. Nach Abschluss der Auswahl zeigt die Funktionsanzeigetaste auf die von Ihnen gewählte Funktion. Bitte beachten Sie das beigefügte Bedienfelddiagramm.
  • Seite 10: Ersatzteile

    Ersatzteile REINIGUNG VERSTOPFTER ENTLÖT-SPITZEN VORSICHT: Lötkolben Dieser Vorgang muss bei hohen Temperaturen durchgeführt werden: • Be sure that the spring wire (included) will not go through the nozzle of the desolder tip. • Adjust the heating element to a higher temperature allowing the clogged solder to melt. Clean the tip by sliding the spring wire up and down until the passage is clear.
  • Seite 11: Auswechseln Der Filter

    3. Drehen Sie den Behälter auf den Kopf (Abb. 12) und schütteln Sie das Lötzinn heraus. Diese Aufgabe muss regelmäßig durchgeführt werden, damit die Station ordnungsgemäß funktioniert. ABB-8 ABB-9 4. Nehmen Sie die Spitze wieder heraus und schütteln Sie das geschmolzene Lot in der Spitze aus Abb. 9, ABB-12 die Spitze sollte nun nicht mehr verstopft sein.
  • Seite 12 Tip chart WECHSELSPITZEN FÜR RND 560-00264 ABB-17 ABB-18 Lötspitzen 5. Ersetzen Sie den alten Baumwollfilter durch einen neuen (Abb. 17 & 18). RND 560-00250 LEITUNGSFILTER 1. Schrauben Sie den Leitungsfilter ab (Abb. 19) und ziehen Sie ihn auseinander (Abb. 20).
  • Seite 13 Lödstation med LCD-pekskärm RND 560-00264 www.rnd-electronics.com VARNING: Läs instruktionerna innan du använder apparaten...
  • Seite 14 Starta Egenskaper Sätt först i nätkabelkontakten i strömkabelkontakten på maskinens baksida och anslut sedan nätkabelns • Lämplig för blyfria lödapplikationer kontakt i eluttaget. Slå på strömbrytaren på apparatens baksida: • Temperaturreglering via LCD-pekskärm • Nollswitch-krets för att undertrycka strömspikar • Hög vilostabilitet •...
  • Seite 15 Inställningsmetoden är som följer: MODELL RND 560-00264 För att välja den funktion du vill ställa in, tryck först på funktionsvalsknappen längst ner på skärmen för att välja SOLDER eller DESOLDER. När valet är slutfört pekar funktionsindikeringsknappen på den funktion du valt.
  • Seite 16 Reservdelar PROCEDUR FÖR RENGÖRING AV IGENSATTA SPETSAR VARNING: Lödpenna Denna procedur ska utföras vid hög temperatur. • Se till att fjädertråden (ingår) inte kommer att passera genom munstycket på avlödningsspetsen. • Justera värmeelementet till hög temperatur så att det igensatta lodet smälter. Rengör spetsen genom att skjuta fjädertråden upp och ner tills passagen är fri.
  • Seite 17 3. Rikta kollektorn nedåt medan du skakar en aning (se Figur 12.) så att avfallslodet faller ut. Detta moment bör utföras regelbundet för att stationen ska fungera korrekt. FIG-8 FIG-9 4. Ta bort igen och skaka ut eventuellt löst smält lod i spetsen enligt Figur 9, spetsen ska nu vara rengjord. FIG-12 Byt ut spetsen och skruva tillbaka hylsmuttern, men ha försiktighet att inte dra åt för hårt! 4.
  • Seite 18 Tip chart UTBYTBARA SPETSAR FÖR RND 560-00264 FIG-17 FIG-18 Lödspetsar 5. Ta bort det gamla bomullsfiltret och byt ut det (se Figur 17 & 18). RND 560-00250 LINJEFILTER RND 560-00251 1. Skruva loss linjefiltret (se Figur 19) och dra sedan isär (Figur 20)
  • Seite 19 www.rnd-electronics.com...

Inhaltsverzeichnis