Landxcape LX835i Benutzerhandbuch Seite 18

7. Software update
The software can be updated when new versions become available. The
latest software can be downloaded from our website
www.landxcape-robotics.com.
Update via USB. See below for download and installation instructions:
(1) Locate the latest software version at: www.landxcape-robotics.
com. Save the file to an empty FAT32 formatted USB (flash drive).
Delete any other files on the drive and check the format. If the drive
is not formatted in FAT32 , please reformat the drive.
TM
(2) Place Landxcape on a secure and level surface. Press
TM
off your Landxcape .
(3) Insert the USB drive (flash drive) in the port. (See Fig. J1)
TM
(4) Turn Landxcape on. The update will begin automatically. Wait until
the display shows " " (See Fig. J2), then remove the USB drive
(flash drive) and tightly close the protective cover. When the display
shows " ", the update is complete and Landxcape
the PIN page.
The manual included with your Landxcape
software at the time of production. Some new features/functions in the
new version may not exist in the manual. If you found some settings not
in the manual, please visit www.landxcape-robotics.com to download
the latest manual.
8. Maintenance
TM
Your Landxcape works hard and needs to be cleaned and checked
from time to time. Some parts will require replacement as they become
TM
worn. Never use your Landxcape
Switch off the machine before carrying out any service or maintenance.
Here's how to take care of your Landxcape
8.1 Keep it sharp
WARNING: Before cleaning, adjusting, or replacing the
blades, turn your Landxcape
gloves.
WARNING: When fitting new blades, make sure you
replace ALL the blades. Always use new screws when
fitting blades. This is important to ensure blade retention and
balance the blade turning disc. Failure to use new screws could
cause serious injury.
TM
Landxcape does not cut grass like other mowers. Its cutting blades
are razor sharp on 2 edges and rotate in both directions for maximum
cutting capacity (See Fig. K). Each blade of your Landxcape
cutting edges. The blade turning disc will make forward and reverse
rotation at random to use both cutting edges and minimize the
frequency of replacing the blades. Each cutting blade will last up to
2 months when it is programmed to mow everyday. Always check to
see if the blades are chipped or damaged and replace them if they
are. When the cutting blades are dull and worn out, they should be
replaced with the spare blades provided with your Landxcape
blades are also available at your nearest Landxcape
A. Replace the Blades
After some time, usually every season, your Landxcape
will need to be replaced. When replacing the blades, make sure to
replace ALL of them at the same time. You can replace them with one
of the spare blade kits and extra blade screws supplied with your
TM
Landxcape .
Before attempting to replace your Landxcape
18
to turn
TM
will enter
TM
is based on the default
with defective main switch.
TM
.
TM
OFF and put on protective
TM
has 2
TM
. Spare
TM
retailer.
TM
's Blades
TM
's blades, turn the
power off and put on protective gloves and follow these steps:
TM
1. Gently flip Landxcape over.
2. Remove the battery cover and remove the battery.
3. Take the screws off the blades with a screwdriver. (See Fig. L)
4. Firmly screw on the new blades.
5. Refit the battery and the battery cover.
IMPORTANT: After screwing the blade to the blade disc, make
sure the blade is able to spin freely.
8.2 Keep it clean
WARNING: Before cleaning, turn your Landxcape
Put on protective gloves before cleaning the blade
turning disc and do not rinse or flush with water.
A. Cleaning the body
TM
Your Landxcape will live a much happier and longer life if it is
cleaned regularly. Although, since your Landxcape
machine, you will need to take care when cleaning. DO NOT use a
hose, high pressure washers and do not pour running water on
your Landxcape TM . It is best to use a spray bottle filled with water.
When cleaning the machine body, use a soft brush or clean cloth and
avoid using solvents or polishes (See Fig. M). Lastly, remove all build
up of grass clippings and debris.
B. Cleaning the Underside
Again, it is important that you power Landxcape
protective gloves before touching the blade turning disc .
TM
First, flip your Landxcape upside down to expose its underside. Here
you will see the blade disc, the chassis, and the front wheel and driving
wheels. Clean everything thoroughly with a soft brush or moist rag.
WARNING: NEVER clean the underside of Landxcape
running water. Component damage can occur. (See Fig. N1,
N2)
Rotate the blade disc to ensure it rotates freely. Check the blades spin
freely around the fixing screws. Remove any obstructions.
IMPORTANT: Remove any lodged debris so that it does not cause
a crack in the blade disc. Even the tiniest crack can decrease
your Landxcape TM 's mowing output.
C. Clean the contact pins and the charging strips
Clean the contact pins located on the charging station and the
charging strips located on Landxcape
up grass clippings or debris around the contact pins and charge strips
TM
periodically to ensure Landxcape
8.3 Battery life
TM
The heart of Landxcape is its 20V Li-Ion battery. For proper storage of
the battery, make sure it is fully charged and kept in a cool dry place.
NOTE: The recommended Landxcape
0
between 0-55 C.
TM
The life-span of Landxcape 's battery depends on various factors, such
as:
• The length of the mowing season in your region
• Amount of hours Landxcape
• Battery maintenance during storage
Landxcape TM can be charged manually without the boundary
wire.
1. Connect the charging station to a suitable power supply.
The green light on the charging station will turn on.
2. Manually dock Landxcape
TM OFF.
TM
is an electric
OFF and wear
TM
TM
with
TM
using a cloth. Remove any built
successfully charges each time.
TM
operation temperature is
TM
mows per day
TM
into the charging station while
EN