Landxcape LX835i Benutzerhandbuch Seite 17

4. Make sure the distance between your Landxcape
close as possible during connection (less than 3 meters).
Step 3: Check your router
1. Make sure your router is 2.4GHz or 2.4GHz mixed 5GHz, and please
enable 2.4GHz band.
2. Make sure your router 802.11 mode of wireless setting is b/g/n
mixed. (See Fig. 1)
3. Make sure your router channel/ band width of wireless setting is
Auto or 20M or 20M mixed 40M. (See Fig. 1)
4. Make sure your router Enable the SSID Broadcast function when
you connect the machine with the APP. And you can close it after you
connect successfully. (See Fig. 1)
5. Make sure DHCP function is enabled. (See Fig. 2)
6. If you have a "Fritz!box" Router, please make sure activate "Allow
communication between devices in same network" in the settings.
7. Mare sure Port 8883 TCP is open. If it's blocked (See Fig. 3), please
modify the setting.
To connect smartphone to your Landxcape
Step 1: To download the Landxcape
download it from Playstore (Google-Android), AppleStore (Apple-iOS) or
our website www.landxcape-robotics.com.
Step 2: Keep pressing
for 3 seconds, the icon
Use or to choose the icon
Only for reference
Step 3: Enter the Landxcape
TM
APP, and then follow the instructions to
EN
TM
and router is as
Fig. 1
Fig. 2
Fig. 3
TM :
TM
App, scan the QR code below or
will be blinking.
, then press to confirm.
connect to your Wi-Fi.
*The Serial No. can be found at the rear of Landxcape
Fig. Q)
NOTE:
1. If your Wi-Fi information changes, Landxcape
according to Step 3.
TM
2. When Landxcape is located in an area with low or no Wi-Fi
signal, instructions sent from the mobile App may not be executed
TM
immediately. Landxcape will receive instructions when it returns
to an area with good Wi-Fi signal.
3. For strong Wi-Fi signal to ensure stable connection, it is
recommended to install Wi-Fi extenders to cover areas with weak
or no Wi-Fi signal.
6. Boundary Wire Basics
6.1. Pegging the Boundary Wire
Use the boundary wire distance gauge to set the correct distance
between the wire and the border of your lawn (more than 26cm).This
is the recommended distance. The provided distance gauge ensures
proper installation.
If your neighbor also uses a Landxcape
metre between your boundary wire and your neighbor's.
The boundary wire must outline the intended mowing area
exactly. Your Landxcape
TM
will become confused by extra bends or
coils of boundary wire that are not part of its mowing area (See Fig.
G). If there is excess boundary wire after the mowing area has been
outlined, cut it off and store this additional wire in a separate location.
It is important to leave the necessary length where it connects to the
charging station so it can be connected and still remain buried.
6.2 Burying the Boundary Wire
If you are planning to bury the boundary wire, it is recommended to first
peg it down. This allows you to easily change the layout if necessary before
burying the wire. When the boundary wire installation is complete, have
TM
Landxcape follow and check the path by pressing
TM
allows your Landxcape to adjust to its new environment. .
TM
While observing Landxcape you can easily make alterations to the
boundary wire to ensure Landxcape
the charging station. Confirm that Landxcape
station successfully, and bury the wire if desired.
6.3 Joining the boundary wire
If you want to extend and splice the boundary wire, use a connector.
The connector is waterproof and provides optimal connection.
Insert both wire ends in any two of the three holes of the connector.
Insert the wires fully until both wire ends are visible on the other side of
the connector. (See Fig. H) Press the connector together by using a pair
of pliers. (See Fig. I1, I2)
WARNING! It is not recommended to simply splice the boundary
wire with insulating tape or use a screw terminal block for
connection. A broken circuit may occur after a period of time as soil
moisture can oxidize the wire.
TM
as shown. (See
TM
needs to be re-set
TM
, keep a spacing of at least 1
and . This
TM
's trouble-free tracking when locating
TM
docks in the charging
17