Manual Tuning - Dab - Makita MR004G Betriebsanleitung

Manual tuning – DAB
Manual tuning allows you to tune your radio to a
particular DAB frequency in Band III. This function can
also be used to assist the positioning of the antenna
or the radio so as to optimize reception for a specific
channel or frequency.
1. Press the Advanced setting button and rotate the
Volume/Tuning Control/Select knob until "Manual
Tune" shows on the display. Press the Volume/Tuning
Control/Select knob to enter the manual tuning mode.
2. Rotate the Volume/Tuning Control/Select knob to
select the desired DAB channel. Press Volume/
Tuning Control/Select knob to confirm the chosen
frequency.
Station order setup – DAB
Your radio has 3 station order settings from which
you can choose. The station order settings are
alphanumeric, ensemble and valid station.
1. Press the Advanced setting button.
2. Rotate the Volume/Tuning Control/Select knob until
"Station Order" appears on the display, then press
the Volume/Tuning Control/Select knob to enter the
setting.
3. Rotate the Volume/Tuning Control/Select knob to
select the following options and press the knob to
confirm the setting.
Alphanumeric Sorts the station list alpha-
numerically 0...9 A...Z.
Ensemble Organizes the station list by DAB
multiplex.
Valid Shows only those stations for which
a signal can be found.
Dynamic Range Control (DRC) – DAB
DRC feature can make quieter sounds easier to hear
when your radio is used in a noisy environment by
reducing the dynamic range of the audio signal. There
are three levels of compression:
DRC 0 No compression applied.
DRC 1/2 Medium compression applied.
DRC 1 Maximum compression applied.
1. Press the Power button to switch on your radio.
2. Press the Band button to select the DAB band.
3. Press the Advanced setting button and rotate the
Volume/Tuning Control/Select knob until "DRC Value"
shows on the display. Then press the Volume/Tuning
Control/Select knob to enter the setting. The display
will show the current DRC value.
4. Rotate the Volume/Tuning Control/Select knob to
select desired DRC setting.
5. Press the Volume/Tuning Control/Select knob to
confirm the setting.
Scan Tuning – FM
Note:
The FM antenna is built into the handle. When operating
the radio, please straighten the handle properly above
the radio to get better reception.
1. Press the Power button to turn on the radio.
2. Press the Band button to select FM band.
3. Press the Auto tune button and the radio will search
and stop automatically when it finds a radio station.
The radio will continue searching for the next
available station unless the operator presses the Auto
tune button to stop the scanning.
4. Rotate the Volume/Tuning Control/Select knob to get
the desired sound level. The LCD display will show
sound level changes.
5. To turn off the radio, press the Power button.
Manual Tuning – FM
1. Press the Power button to turn on the radio.
2. Press the Band button to select FM band.
3. Press the Volume/Tuning Control/Select knob to
switch to the tuning control mode.
4. Rotate the Volume/Tuning Control/Select knob to find
your desired station.
5. To adjust the volume, press the Volume/Tuning
Control/Select knob again to switch to the volume
control mode.
6. Rotate the Volume/Tuning Control/Select knob to
adjust the sound level as required.
FM scan zone
When using FM mode, your radio can be set to scan
either local stations or to scan all stations including
distant radio stations.
1. Press the Power button to turn on the radio.
2. Press the Band button to select the FM band.
3. Press the Advanced setting button and then rotate
the Volume/Tuning Control/Select knob until "FM
Scan Zone" shows on the display. Press the Volume/
Tuning Control/Select knob to enter the setting.
4. Rotate the Volume/Tuning Control/Select knob to
switch between "Local" (Strong stations only) and
"Distant" (All stations) options on the lower line of the
display. The Distant option will allow the radio to find
weaker signals when scanning.
5. Press the Volume/Tuning Control/Select knob to
confirm your selection. The Local or Distant setting is
stored in the radio and remains in force until changed
or until a System Reset.
10 ENGLISH