Bosch GTB 185-LI Professional Originalbetriebsanleitung Seite 13

Technical Data
Cordless screwdriver
Article number
Rated voltage
A)
No-load speed
Max. torque, soft screwdriv-
ing application according to
A)
ISO 5393
Tool holder
Max. screw diameter
Weight according to
B)
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation and
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20–25 °C with rechargeable battery GBA 18V
2.0Ah.
B) Measured with GBA 18V 1.5Ah and GBA 18V 12Ah.
C) Limited performance at temperatures < 0 °C
Noise/vibration information
Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 76 dB(A); sound power level
87 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Impact tightening of fasteners of the maximum capacity of
2
the tool: a < 2.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
Bosch Power Tools
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
GTB 185-LI
over the total working period.
Implement additional safety measures to protect the oper-
3 601 JK7 0..
ator from the effects of vibration, such as servicing the
V= 18
power tool and application tools, keeping their hands warm,
-1
min 0–4500
and organising workflows correctly.
Nm 5.0
Assembly
u
¼" internal
hexagon
mm 6
kg 1,3–2,3
Battery Charging
°C 0 to +35
u
°C –20 to +50
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
GBA 18V...
before using your power tool for the first time.
ProCORE18V...
The lithium-ion battery can be charged at any time without
GAL 18...
reducing its service life. Interrupting the charging process
GAX 18..
does not damage the battery.
GAL 36...
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Follow the instructions on correct disposal.
Removing the battery
The battery (7) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (8) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (7), press the release button (8) and
pull the battery forward and out of the power tool. Do not
2
use force to do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 6HJ | (23.09.2021)
English | 13
to