EGO LB6002E Bedienungsanleitung Seite 13

2. First attach the cylindrical tube onto the middle tube.
Align either of the grooves in the cylindrical tube with
the knob on the middle tube (Fig. D).
3. Push the middle tube forward until the knob engages
either of the grooves. Then rotate the middle tube in
the direction of the arrow until the knob slides into the
lock position (Fig. E).
Fig. C & D parts description see below:
C-1 Cylindrical Tube D-1
C-2 Curved Flat Tube D-2
C-3 Middle Tube
NOTICE:
Before the middle tube is locked into place
during rotation, you will notice a built-in stop that will
create some resistance. Continue to rotate the tube past
the stop until it slides fully into the lock position.
4. You may shorten or lengthen the tube length according
to your preference by locking the middle tube into
different lock positions (Fig. F).
Fig. F parts description see below:
F-1 First lock position
F-2 Second lock position
5. Attach the tube assembly onto the blower housing in
the same way (Fig. G).
Follow the same sequence to assemble the curved flat
tube with the blower.
6. To remove the tube assembly from the blower housing
or to separate the two tubes, first turn the tube in the
unlocking direction to disengage the latch and then
pull the tube straight outward.
OPERATION
WARNING:
Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING:
Do not use any attachments or
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
WARNING:
Always remove the battery pack from
the product when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing the
battery pack will prevent accidental starting that could
cause serious personal injury.
56 VOLT LITHIUM-ION CORDLESS BACKPACK BLOWER — LB6000E
Before each use, inspect the entire product for damaged,
missing, or loose parts, such as screws, nuts, bolts,
caps,etc. Tighten securely all fasteners and caps and
do not operate this product until all missing or damaged
parts are replaced.
WARNING:
the chest buckle straightly to take off the blower.
APPLICATION
Knob
You may use this product for the purposes listed below:
Grooves for different
◾
Clearing hard surfaces such as driveways and walkways.
lock positions
◾
Keeping decks and driveways free from leaves and
pine needles.
NOTICE:
purpose. Any other use is deemed to be a case of misuse.
INSTALLING/REMOVING THE BATTERY PACK
CHARGE BEFORE FIRST USE.
Use only with battery packs and chargers listed fig.A
NOTICE:
the EGO 56V Battery BA2800 (5.0 Ah) or any EGO 56V
battery with higher capacity.
◾
To Install (Fig. H)
Align the battery ribs with the mounting slots and press
the battery pack down until you hear a "click".
◾
To Remove (Fig. I)
Depress the battery-release button and pull the battery
pack out.
WARNING:
your feet, children, or pets when pressing the battery-
release button. Serious injury could result if the battery
pack falls. NEVER remove the battery pack when in a high
location.
POSITIONING THE BACKPACK BLOWER
WARNING:
injury when operating this tool. Do not wear loose clothing
or jewelry. Wear eye and ear/hearing protection. Wear
heavy, long pants, boots and gloves. Do not wear short
pants or sandals or go barefoot.
To Adjust The Support Harness
1. Put your arms through the backpack straps to support
the blower on your back.
2. Temporarily adjust both shoulder straps to comfortable
positions (Fig. J), making sure that your elbow is
comfortable.
3. Snap the chest buckle and adjust its length if
necessary (Fig. K).
If you encounter an emergency, separate
The tool is to be used only for its prescribed
For best performance, we recommend use of
Always take care to note the location of
Dress properly to reduce the risk of
EN
11