Inhaltsverzeichnis
Werbung
EN - Instructions for use of safe RS.30R.LA/RS.45R.LA
Package contents
1x steel safe, 2x emergency key, 4x AA batteries, 1x external source, 1x inner shelf, 1x inner felt, 4x steel dowel and screw
Opening the safe for the first time
Remove the protective cover of the lock (Fig. A, No. 1, page 17) and insert the emergency key.
Turn the key (keep the key in the unlocked position) and then turn the handle (Fig. A, No. 2) clockwise approximately 90°.
The lock is unlocked and the door is open.
In this way, the safe can always be opened, e.g. if the code is forgotten, the batteries run out, or the lock electronics are not
working.
ATTENTION: Never leave the emergency key in the safe, store it in a safe place!
Battery location
Remove the battery cover from the inside of the door (by sliding it towards the hinges, Fig. B, No. 9, page 17).
Insert 4pcs AA batteries, you will hear 3x "beep" and the LCD display (Fig. A, No. 4) will show "GOOD" within a few seconds.
Replace the battery cover. The safe can now be used.
Note: If the LCD display (Fig. A, No. 4) shows "LO-BATTE", it means that the batteries are low. Replace the batteries
immediately.
Setting the user code
Factory setting is 1234.
Press the red button on the back of the door (Fig. B, No. 8), you will hear a "beep".
"--------" will be displayed on the LCD display (Fig. A, No. 4).
On the front of the door (keypad, Fig. A, No. 5), enter your 3-8 digit code from numbers, confirm it with the "#" button (Fig.
A, No. 7).
The LCD display (Fig. A, No. 4) will display "IN". This confirms the correct setting of the user code (at the same time, the old
code is cancelled).
Setting the master code
Factory setting is 123456.
Open the door and press "#" (Fig. A, No. 7), then press "0" twice, press the "reset" button (Fig. B, No. 8), on the LCD display
(Fig. A, No. 4 ) will be displayed "--------".
On the front of the door (keypad, Fig. A, No. 5), enter your 3-8 digit code from numbers, confirm it with the "#" button (Fig.
A, No. 7).
The LCD display (Fig. A, No. 4) will display "IN". This confirms the correct setting of the master code (at the same time, the
old code is cancelled).
Opening the door using a user/master code
Press "#" (Fig. A, No. 7), LCD (Fig. A, No. 4) will show "--------".
Enter the user/master code (each key press is accompanied by a beep), press "#" (Fig. A, No. 7), the LCD will display
"OPEN".
Turn the handle (fig. A, no. 2) clockwise by approx. 90° and open the door within five seconds.
After entering an incorrect code, the LCD display (fig. A, no. 4) will display the inscription "ERROR".
To delete any incorrectly entered number, press "*" (Fig. A, No. 6).
ATTENTION: If you enter an incorrect code three times in a row, a warning acoustic signal will be activated for 20 seconds.
If you re-enter an incorrect code three times, a warning acoustic signal will be activated for 20 seconds and the locking
mechanism and keypad will be blocked for 2 minutes and 40 seconds.
Closing the safe
Close the door and turn the handle counterclockwise to a vertical position.
An electronic mechanism locks the door.
Secure View feature
Your safe is equipped with a "Secure View" feature.
Using this function means that your code will not be shown on the display when you enter it.
Press "#" (Fig. A, No. 7) to launch the keyboard.
Press "*" (fig. A, no. 6) to start the security function. Any code you enter will be displayed as "oooooooo" on the LCD display
(Fig. A, No. 4), this will ensure the security of your code.
To cancel this function, press "#" (Fig. A, No. 7) and "*" twice (Fig. A, No. 6).
Alarm
You can set an alarm in case someone tries to break into the safe.
Press "*" (fig. A, no. 6).
"ALERT on" will appear on the display.
The safe will sound an alarm for 20 seconds when the safe is shaken.
Press "#" (Fig. A, No. 7) to disarm the alarm, enter the correct user/master code and press "#" (Fig. A, No. 7) to confirm.
External source
If the batteries run out, it is also possible to use an external source to open the safe.
Open the external source (by sliding the cover away from the cable).
Insert 4pcs AA batteries. Close the external source.
Connect the external power source to the safe using a cable (Fig. A, hole No.3).
Then follow the instructions - "Opening the door using the user/master code".
ATTENTION: Never leave an external power source in a safe, store it in a safe place!
Assembly method
Place the safe in a place where it is not easy to move.
Open the safe and use the screw anchor holes as a drilling template.
Drill the holes for the expansion screws in the right place with a ø 9mm drill bit.
Use expansion screws (fig. C, page 17) to fix the safe to the wall.
Holes for anchoring safes
4x hole in the floor, 4x hole in the wall
ATTENTION: For a wall other than brick or concrete, use screws and dowels suitable for the wall or floor of your choice.
CZ
SK
DE
EN
HR
HU
IT
NL
PL
RO
SLO
SRB
UA
7
Werbung
Inhaltsverzeichnis
