Before Using The Equipment; Mains Connection - EINHELL TC-AC 190 OF Set Originalbetriebsanleitung

5. Before using the equipment

Before you connect the equipment to the power
supply make sure that the data on the rating plate
are identical to the supply voltage.
•
Check the equipment for damage which may
have occurred in transit. Report any damage
immediately to the transport company which
was used to deliver the compressor.
•
Install the compressor in the vicinity of the
point of consumption.
•
Avoid long air lines and supply lines (extensi-
on cables).
•
Make sure that the intake air is dry and dust-
free.
•
Do not install the compressor in a damp or
wet room.
•
The compressor may only be used in suitable
rooms (with good ventilation and an ambient
temperature from +5 °C to 40 °C). There must
be no dust, acids, vapors, explosive gases or
inflammable gases in the room.
•
The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor
in areas where work is conducted with spray-
ed water.
•
Operate the equipment only on a firm, level
surface.
•
During operation place the compressor on the
rubber feet on the back of the compressor.
•
Important! When you switch off the compres-
sor, excess air will escape at the safety valve.
This is not a fault, but arises in connection
with the equipment's construction.
6. Operation

6.1. Mains connection:

Before you use the machine, make sure that the
mains voltage complies with the specifi cations on
the rating plate. Long supply cables, extensions,
cable reels etc. cause a drop in voltage and can
impede motor start-up. At low temperatures below
+5°C, sluggishness may make starting diffi cult or
impossible.
6.2 On/Off switch (4)
To switch on the equipment set the On/Off switch
(4) to position 1.
Move the On/Off switch (4) to position 0 to switch
off the equipment.
Anl_TC_AC_190_OF_Set_SPK13.indb 19 Anl_TC_AC_190_OF_Set_SPK13.indb 19
GB
6.3 Compressed air hose with quick-lock
coupling (3)
Connecting:
Insert the nipple of the air tool into the quick-lock
coupling, the sleeve will spring forward automa-
tically.
Disconnecting:
Pull back the sleeve and remove the tool. Cauti-
on! When releasing the quick-lock coupling, be
sure to hold the coupling piece to protect yourself
against injury from the rebounding hose.
6.4 Tire pressure gauge with adapters (Fig. 2)
Working pressure in bar: 0-8
Range of applications:
The tire pressure gauge allows you to infl ate tires
easily and exactly. Use the pressure gauge to
check the tire pressure. If the tire pressure is too
high, you can reduce the pressure with the integ-
rated relief valve (e).
After fi lling with air, please check the set tire
pressure with a calibrated gauge, for example at a
petrol station.
The tire pressure gauge comes with a valve adap-
ter for car tire valves.
Other valve types can be fi lled using the supplied
adapters.
Using the equipment as a blow-out pistol
(Fig. 3)
To use the tire pressure gauge as a blow-out
pistol you must fi rst unscrew and remove the
hose with the valve adapter for care tires. Now the
blow-out adapter (7) can be screwed to the tire
pressure gauge.
Range of applications:
For cleaning and blowing out hollow spaces or
hard-to-reach areas, as well as for cleaning soiled
equipment. The infi nitely variable trigger lever al-
lows an exact dosing of compressed air.
Do not exceed the maximum permissible opera-
ting pressure of 8 bar (also shown on the back of
the tire pressure gauge).
- 19 -
08.05.2023 08:35:08 08.05.2023 08:35:08