HIKVISION DS-2DE7A412MCG-EB Kurzanleitung Seite 19

2006/66/EC (battery directive): This
product contains a battery that cannot be
disposed of as unsorted municipal waste in
the European Union. See the product
documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated
collection point. For more information, please see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
이 기기는 업무용 환경에서 사용할 목적으로
적합성평가를 받은 기기로서 가정용 환경에서
사용하는 경우 전파간섭의 우려가 있습니다.
Safety Instruction
Warnings
Laws and Regulations
The device should be used in compliance with local
laws, electrical safety regulations, and fire prevention
regulations.
Electrical Safety
CAUTION: To reduce the risk of fire, replace only with
the same type and rating of fuse.
This equipment shall be installed incorporated with
UPS to avoid the risk of restart.
Battery
This equipment is not suitable for use in locations
where children are likely to be present.
CAUTION: Risk of explosion if the battery is replaced
by an incorrect type.
Improper replacement of the battery with an
incorrect type may defeat a safeguard (for example,
in the case of some lithium battery types).
Do not dispose of the battery into fire or a hot oven,
or mechanically crush or cut the battery, which may
result in an explosion.
Do not leave the battery in an extremely high
temperature surrounding environment, which may
result in an explosion or the leakage of flammable
liquid or gas.
Do not subject the battery to extremely low air
pressure, which may result in an explosion or the
leakage of flammable liquid or gas.
Dispose of used batteries according to the
instructions.
Cautions
Fire Prevention
No naked flame sources, such as lighted candles,
should be placed on the equipment.
The serial port of the equipment is used for
debugging only.
Hot Surface
CAUTION: Hot parts! Burned fingers when handling
the parts.
This sticker is to indicate that
the marked item can be hot and
should not be touched without taking care. Wait
one-half hour after switching off before handling
parts.
The device with this sticker is intended for
installation in a restricted access location. Access can
only be gained by service persons or by users who
have been instructed about the reasons for the
restrictions applied to the location and about any
precautions that shall be taken.
Installation
Install the equipment according to the instructions in
this manual.
To prevent injury, this equipment must be securely
attached to the ceiling/wall in accordance with the
installation instructions.
Be sure that there is enough space to install the
device and accessories.
Make sure that the wall is strong enough to
withstand at least 8 times the weight of the device
and the mount.
Make sure that the power has been disconnected
before you wire, install, or disassemble the device.
Transportation
Keep the device in original or similar packaging while
transporting it.
Do not drop the product or subject it to physical
shock.
Power Supply
The power source should meet limited power source
or PS2 requirements according to IEC 60950-1 or IEC
62368-1 standard.
Refer to the device label for the standard power
supply. Please make sure your power supply matches
with your device.
Use a power adapter provided by qualified
manufacturers. It is recommended to provide an
independent power adapter for each device as
adapter overload may cause over-heating or a fire
hazard.
System Security
Please understand that you have the responsibility to
configure all the passwords and other security
settings about the device, and keep your user name
and password.
Maintenance
If the product does not work properly, please contact
your dealer or the nearest service center. We shall
not assume any responsibility for problems caused by
unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor)
require regular replacement. The average lifespan
varies, so periodic checking is recommended. Contact
your dealer for details.
Cleaning
Please use a soft and dry cloth to clean the interior
and exterior surfaces. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that
the device lens is not exposed to the laser beam, or it
may burn out.
Do not aim the lens at the sun or any other bright
light.
To avoid heat accumulation, good ventilation is
required for a proper operating environment.
18