Технические Характеристики - BEMKO SES05BL-B Bedienungsanleitung

CONNECTION:
Warning. Danger of death through electric shock!
 Must be installed by professional electrician.
 Disconnect power source.
 Cover or shied any adjacent live components.
 Ensure device cannot be switched on.
 Check power supply is disconnected.
 Please move the upper cover with anti-clockwise whirl as per the diagram on the right.
 Connect the power and the load according to the connection-wire diagram.
 Fix the bottom on the selected position with the inflated screw.
 Install back the upper cover on the sensor, then you could switch on the power and test it
CONNECTION-WIRE DIAGRAM:
(See the right figure)
TEST:
 Turn the TIME knob anti-clockwise on the minimum(10s).Turn the LUX knob clockwise on the maximum
(sun).
 Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After
Warm-up 30sec, the sensor can start work .If the sensor receives the induction signal, the lamp will turn
on. While there is no another induction signal any more, the load should stop working within 10sec±
3sec and the lamp would turn off.
 Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is more than 3LUX, the sensor
would not work and the lamp stop working too. If you cover the detection window with the opaque
objects (towel etc), the sensor would work .Under no induction signal condition, the sensor should
stop working within 10sec±3sec.
Note: when testing in daylight, please turn LUX knob to (SUN)
lamp could not work! If the lamp is more than 60W, the distance between lamp and sensor should be
60cm at least.
SOME PROBLEM AND SOLVED WAY:



RU
Широкое поле улавливания покрывается с помощью датчиков. Работа основана на получении ИК лучей
человеческого тела. Когда кто-то входит в поле улавливания, датчик в то же время включает питание
как днем, так и ночью; монтаж его очень удобный, а использование очень широкое.
ТЕХНИЧЕСКИЕ ХАРАКТЕРИСТИКИ:
Напряжение питания: 220-240V/AC
Частота питания: 50Hz
Время задержки:Min.10sec±3sec;
Номинальная нагрузка: Max. 400W
position, otherwise the sensor
Высота монтажа: 2.2-4m
The load do not work:
a. Please check if the connection-wiring of power and load is correct.
b. Please check if the load is good.
c. Please check if the working light sets correspond to ambient light.
The sensitivity is poor:
a. Please check if there has any hindrance in front of the detection window to affect to receive
the signal.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection fields.
d. Please check if the installation height corresponds to the height showed in the instruction.
e. Please check if the moving orientation is correct.
The sensor can not shut off the load automatically:
a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is the longest.
c. Please check if the power corresponds to the instruction.
Даный продукт является новым энергосберегающим выключателем; он соединил в себе
высокую чувствительность датчика, встроенную микросхему, автоматику, удобство в
использовании, безопасность, энергосбережение и практическую функциональность.
Max.7min±2min
200W + LED
Угол улавливания: 360°
Расстояние улавливаиня: Ø8м max(<24℃)
Окружающий свет: <3-2000LUX(регулируется)
Рабочая температура: -20~+40℃
Рабочая влажность: <93%RH
Потребляемая мощность: прибл 0.5W
Обнаруживаемая скорость движения: 0.6-1.5m/s