CONSTRUCTOR CHAGD2003-BM Übersetzung Der Originalanleitung Seite 14

storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
Store power tools, when not in use, out of the
reach of children and do not allow people who are
not familiar with the power tool or these instructions
to operate it. Power tools are potentially dangerous
in the hands of untrained users.
Maintain power tools. Check for misalignment or
jammed moving parts, breakages or any other
feature that might affect the operation of the power
tool. If it is damaged, the power tool must be
repaired. Many accidents are caused by using
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to jam and are easier to control.
Use the power tool, accessories and cutting tools,
etc., in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work which needs to be done. Using a power
tool in ways for which it was not intended can lead
to potentially hazardous situations.
Service
Your power tool should be serviced by a qualified
specialist using only standard spare parts. This will
ensure that it meets the required safety standards.
WARNING: Packaging materials
are not toys! Children must not
play with plastic bags! Danger of
SYMBOLS
ADDITIONAL SAFETY
INSTRUCTIONS FOR HEAT GUNS
_ Do not place your hand over the air vents or block
the vents in any way.
_ The nozzle and accessories of this tool become
extremely hot during use. Let these parts cool down
before touching.
_ Always switch the tool off before putting it down.
_ Do not leave the tool unattended while it is
switched on.
_ A fire may arise if the appliance is not used with
care.
_ Heat may be conducted to combustible materials
that are out of sight. Do not use in a
suffocation!
Read manual before use
In accordance with
essential applicable
safety standards of
European directives
Double insulated
damp atmosphere where flammable gases may be
present or near combustible materials.
_ Allow the tool to cool fully before storing.
_ Ensure adequate ventilation as toxic fumes may
be produced.
_ Do not use as a hairdryer.
_ Do not obstruct either the air intake or nozzle
outlet, as this may cause excessive heat
build up resulting in damage to the tool.
_ Do not direct the hot air blast at other people.
_ Do not touch the metal nozzle as it becomes very
hot during use and remains hot for up to
30 minutes after use.
_ Do not place the nozzle against anything while
using or immediately after use.
_ Do not poke anything down the nozzle as it could
give you an electric shock. Do not look
down the nozzle while the unit is working because
of the high temperatures being produced.
_ Do not allow paint to adhere to the nozzle or
scraper as it could ignite after some time.
_ A fire may result if the appliance is not used with
care, therefore
- be careful when using the appliance in places
where there are combustible materials;
- do not apply to the same place for a long time;
- do not use in presence of an explosive
atmosphere;
- be aware that heat may be conducted to
combustible materials that are out of sight;
- place the appliance on its stand (vertical, nozzle
pointing upwards) after use and allow it to cool
down before storage;
- do not leave the appliance unattended when it is
switched on.
REMOVING PAINT
_ Do not use this tool to remove paint containing
lead. The peelings, residue and vapours of
paint may contain lead, which is poisonous. Any
pre-1960 building may have been painted in the
past with paint containing lead and covered with
additional layers of paint.
_ Once deposited on surfaces, hand to mouth
contact can result in the ingestion of lead.
Exposure even to low levels of lead can cause
irreversible damage to the brain and nervous
system. Young and unborn children are particularly
vulnerable.
_ When removing paint, ensure that the work area is
enclosed. Preferably wear a dust mask.
_ Do not burn the paint. Use the scraper provided
and keep the nozzle at least 25 mm away from the
painted surface. When working in a vertical
direction, work downwards to prevent paint from
falling into the tool and burning.
_ Dispose of all paint debris safely and ensure that
the work area is thoroughly cleaned after
completing the work.
14