Optional Accessories; Protecting The Environment; Rechargeable Battery Pack - DeWalt DCMPW1600 Originalanweisung

Optional Accessories


WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
w
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be

WARNING: Risk of Unsafe Operation. Before servicing unit unplug or disconnect electrical supply, turn water supply
off, discharge residual pressure, and engage spray handle lock-off.
PROBLEM
Motor does not start.
Unit does not reach high pressure.
Output pressure varies high/low.
No detergent.
Garden hose connection leaks.
Suction hose does not self prime.
Spray wand or extension leaks.
Pump is excessively noisy.
Water leaks from pump.
Oil leaks.
Motor buzzes but fails to run.
WALT-recommended
e
TROUBLESHOOTING
caUsE
Battery packs not installed properly.
Battery packs not charged.
Speed selector switch is in the OFF position.
Wand trigger not being squeezed.
Battery port door is not latched.
Water faucet not fully turned on.
Water inlet filter clogged.
Nozzle worn.
Pump is sucking air.
Water supply restricted.
Not enough inlet water supply.
Pump is sucking air.
Water inlet screen clogged.
Discharge nozzle is obstructed.
Soap bottle is empty.
Soap bottle not properly connected.
Detergent is too thick.
Damaged or clogged detergent suction ports.
Discharge nozzle is obstructed.
Flow control knob closed.
Loose fittings.
Missing/worn rubber washer.
Loose fittings.
Filter not fully submerged.
Allow more time for pump to prime.
Spray wand not properly attached.
Broken O-ring.
Pump is sucking air.
Loose fittings.
Water seals are damaged or worn.
Oil seals are damaged or worn.
System has residual pressure.
Pressure washer was not used for long periods.
recovered or recycled, reducing the demand for raw materials.
Please recycle electrical products and batteries according to local
provisions. Further information is available at www.2helpU.com.

Rechargeable Battery Pack

This long-life battery pack must be recharged when it fails to produce
sufficient power on jobs that were easily done before. At the end of
its technical life, discard it with due care for our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
cORREcTIOn
Check battery pack installation.
Check battery pack charging requirements.
Toggle switch to the HI or LO position.
Squeeze trigger with switch in ON position.
Press battey port door fully closed and ensure the battery port door lock is in the locked position.
Open water valve fully.
Remove filter and rinse to clean.
Replace with new nozzle.
Check that hoses and fittings are air tight. Turn OFF machine and purge pump by squeezing trigger until a steady
flow of water emerges from the nozzle.
Check water hose for kinks, leaks and blockage.
Turn water on full force - check hose for leaks and kinks.
Check that hoses and fittings are air tight. Turn OFF machine and purge pump by squeezing trigger until a steady
flow of water emerges from the nozzle.
To unclog, rinse off with water.
Blow out or remove debris.
Add more detergent.
Check connections. Ensure that the soap bottle is fully secured to the spray wand.
Use detergent recommended for use in pressure washers only. Follow manufactures dilution directions.
Remove obstruction or debris and run warm water over the detergent suction ports.
Blow out or remove debris. Run warm water through nozzle to remove debris
Adjust the flow control knob on the top of the high pressure foam cannon.
Tighten fittings.
Replace washer in hose adapter.
Tighten fittings.
Adjust float and ensure filter stays fully covered with liquid.
It could take several minutes at first to self prime. Ensure unit is on and trigger is being squeezed.
Please refer to Assembling Spray Wand under Assembly and Adjustments.
Contact D WALT customer service representative at 1-800-4-D
e
Check that hoses and fittings are air tight. Turn OFF machine and purge pump by squeezing trigger until a steady
flow of water emerges from the nozzle.
Check that all fittings are tight.
Contact D WALT customer service representative at 1-800-4-D
e
Contact D WALT customer service representative at 1-800-4-D
e
Turn unit off, squeeze trigger on spray wand to release pressure, then turn unit on.
Contact D WALT customer service representative at 1-800-4-D
e
EnGLIsh
WALT (1-800-433-9258).
e
WALT (1-800-433-9258).
e
WALT (1-800-433-9258).
e
WALT (1-800-433-9258).
e
45