DeWalt DCMPW1600 Originalanweisung Seite 45

Proper Hand Position (Fig. O)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the spray handle
grip 5 and the other hand on the spray handle
Correct Pressure Washer Unit Position
(Fig. A, C)

CAUTION: Before operation:
Always keep the unit right-side up with its feet
wheels 15 on the ground as shown in Fig. C.
nOTE: Never attempt to use the pressure washer while standing
vertically, on its side, or flipped over on the ground.
Speed Selector Switch (Fig. A, P)
This pressure washer gives you the choice to operate at a high
pressure or lower pressure for more delicate jobs, and can also
boost pressure for high-performance cleaning.
The speed selector switch 9
- Off, centered.
- HI, right side.
- LO, left side.
To turn the pressure washer ON, toggle the speed selector
switch 9 to the right or left positions.
To turn the pressure washer OFF, toggle the speed selector
switch 9 to the center position.
For higher pressure washing, press the speed selector
switch 9 to the right to the "HI" position. This mode is best for
applications that need higher pressure/Bar.
For lower pressure washing, press the speed selector
switch to the left to the "LO" position. This mode is best for
9
projects that require a more delicate cleaning. This mode also
generally offers more runtime.
nOTE: When in "HI" mode, runtime will be decreased as
compared to when pressure washer is in "LO" mode.
To activate Boost mode, press the boost button
green LED will illuminate when activated. This mode is best for
applications that require maximum available Bar.
nOTE: Boost mode will only function for up to ten minutes.
You can press the boost button
before ten minutes and you will go back to the mode the
speed selector switch 9 is set to. When you near the end of ten
minutes the green LED will start to flash, and the unit will return
to the mode the speed selector switch
mode times out.
nOTE: After boost mode is used for a full ten minutes, the unit
can return to boost mode by re-pressing the boost button
nOTE: Overall runtime will be shortened by using boost mode.
4 .
16 and
toggles to three positions;
19 , the
19 again to exit boost mode
9 is set to after boost
Pressure Washing (Fig. A–P)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Preparing Surface for Cleaning
• Remove objects from the area which could create a hazard
such as children's toys or outdoor furniture.
• Insure that all doors and windows are closed tight. Protect
all plants and trees in the adjacent area with a drop cloth
ensuring that they will not be harmed by any overspray.
• Pre-rinse cleaning area with fresh water.
• Use only detergents formulated for pressure washers.
• Always test detergent in an inconspicuous area before use.
Preparing Pressure Washer Unit for Use

DANGER: Risk of fluid injection and laceration. When
using the high-pressure setting, DO NOT allow the
high-pressure spray to come in contact with unprotected
skin, eyes, or with any pets or animals. Serious injury
will occur.

CAUTION: Before operation:
1. Connect the high pressure hose to the pressure washer
and the pressure wand. For instructions on connecting the
high pressure hose to the pressure washer and pressure
wand, please refer to Attaching High Pressure Hose under
Assembly and Adjustments.
2. Connect the water supply to the pressure washer. For
instructions on connecting the water supply to the pressure
washer, please refer to Attaching Garden Hose under
Assembly and Adjustments.
3. Install the two battery packs
port door 20
please refer to To Install the Battery Packs under Installing
and Removing the Battery Packs.
Preparing Spray Wand (Fig. A, F)
IMPORTanT: Before turning on the pressure washer unit,
disengage the trigger lock-off
1. Spray wand must be assembled before use. Please
refer to Assembling Spray Wand under Assembly
and Adjustments.
2. Disengage the trigger lock-off
3. Turn on the water supply.
4. Squeeze the trigger
purge the system of air.
5. If air is still found in the water stream, continue to run water
through the spray wand.
19 .
Cleaning a Surface (Fig. P)
1. To start the pressure washer, toggle the speed selector
switch 9 to the HI or LO position.
2. The best angle for spraying water against a cleaning surface
is 45 °.
35 . Close and lock the battery
. Ensure the door is fully latched into position,
6 and squeeze the trigger
6 .
7 . Hold the trigger for 30 seconds to
EnGLIsh
7 .
43