DeWalt DCMPW1600 Originalanweisung Seite 44

EnGLIsh
• A wide fan pattern distributes the impact of the water over
a larger area, resulting in excellent cleaning action with a
reduced risk of surface damage. Large surface areas can be
cleaned more quickly using a wide fan pattern.
To Attach the Self Priming Suction Hose (Fig. K)
Use the self priming suction hose to pull water from a bucket or
other fresh water source.
NOTICE: Do not use to suction soap, chemicals, dirty
or corrosive liquids, such as window cleaner, plant food,
fertilizers or bleach. Do not use with salt water.
nOTE: Avoid cross threading when installing the self priming
suction hose 28 . Cross threading will cause leaks.
1. To connect the self priming suction hose
pressure washer unit
onto the water intake
2. Securely tighten the suction hose collar
nOTE: Always disconnect the suction hose after usage.
3. Place other end of suction hose, with the filter
a container of fresh water or a fresh water source.
4. Adjust the float ball 29
stays covered in the liquid.
5. Select the correct nozzle to be used. Attaching Nozzles
6. After the job being performed is complete, place the suction
hose into a container of clean water and draw the clean
water through the system to rinse.
nOTE: When using the self priming suction hose, it may
take a few minutes for the pressure washer to self prime.
Ensure the pressure washer is turned on and the trigger on
the spray wand it being pulled until primed.
Attaching High Pressure Foam Cannon (Fig. L)
1. To connect the high pressure foam cannon
spray wand 2 , press the nozzle button
soap bottle.
2. Release the nozzle button
foam cannon 26 in place.
3. Give the high pressure foam cannon
ensure it is locked into place.
nOTE: The soap bottle should be positioned underneath the
spray wand. Do not position the high pressure foam cannon
above the spray wand as this will lead to soap dripping on the
spray wand. The spray tip on the high pressure foam cannon
rotates for vertical or horizontal application.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
42
28 to the
8 , thread the suction hose collar
17 .
31 by hand.
30
on the suction hose so the filter
26 to the
3 and insert the
to lock the high pressure
3
26 a firm tug after to
Installing and Removing the Battery Packs
(Fig. M, N)
This pressure washer is designed to operate on two battery
packs of equal capacity. The pressure washer will not operate
on a single battery pack, and If using different capacity battery
packs, the smaller capacity battery pack, when depleted, will
cause the unit to turn off
nOTE: For best results, make sure your battery packs are both
fully charged.
To Install the Battery Packs

WARNING: Ensure speed selector switch is in the OFF,
centered position, before installing battery packs.

CAUTION: Unit stops running when the battery port
31
door is open. If the speed selector switch is in the HI or LO
position the unit will power ON when the battery port
door closes.

CAUTION: Do not hold the trigger when closing the
on it, into
battery port door.
1. Unlock the battery port door
door latch
30
port door open to access the battery port.
2. Align the battery packs
port and slide them in until the battery packs are firmly
seated in the tool and ensure that they will not disengage.
3. Lock the battery port door
door 20
4. Rotate the battery port door latch
the battery port door. Ensure the battery port door is fully
latched into position before starting tool.
nOTE: The unit will not operate if the battery port door is
not fully closed and latched.
To Remove the Battery Packs
1. Rotate the battery port door latch
and pull the battery port door open to access the battery
packs 35
2. Press the battery release buttons
packs 35
3. Insert the batteries into a charger as described in the
charger section of this manual.
4. Close the battery port door
pressure washer unit
door is fully latched into position.
26
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge, which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 43 . A combination of the three green LED lights will
illuminate, designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
20 , rotate the battery port
21 counterclockwise and swing the battery
35 with the rails inside the battery
20 , close the battery port
so it seals to the pressure washer unit
21
21
.
36
and firmly pull the battery packs out of tool.
20 so it seals to the
8 and lock it. Ensure the battery port
8 .
clockwise to lock
counterclockwise
on the battery