Technical Data - MAC Audio ZXS 1500 D Bedienungsanleitung, Garantie

Dear MAC AUDIO Customer,
The ZXS 1500 D car hi-fi power amplifier will enable you to satisfy your high demands on sound reproduction in your car. With its impressive
deep-bass power reserves, low harmonic content and neutral reproduction, the ZXS 1500 D takes car hi-fi to new heights. The amplifier
is characterized by low operating current, rapid switching capabilities and excellent temperature stability. Experience and enjoy how this
high-tech machine perfectly reproduces magnificent sound.
Please read all of the owner's manual before installing and using the amplifier.
1.

TECHNICAL DATA

Max. output power (1 kHz sinus burst 2:8, B+=14.4V)
Nominal output power (DIN 45 324, B+=14.4V)
Max. output power (1 kHz sinus burst 2:8, B+=14.4V)
Nominal output power (DIN 45 324, B+=14.4V)
Max. output power (100 Hz sinus burst 2:8, B+=14.4V)
Nominal output power (DIN 45 324, B+=14.4V)
Loudspeaker impedance
Frequency response
Total harmonic content (DIN 45 403)
Weighted noise distance (IEC A)
Input sensitivity LOW LEVEL INPUT
Input impedance LOW LEVEL INPUT
Low-pass filter
Subsonic filter
Bass boost
Supply
Fuse
Sizes (W x H x D)
Weight
SUBJECT TO TECHNICAL CHANGE
2. FEATURES
· Digital high-performance power amplifier with a very high efficiency
· Stable at 1 ohm
· Low-pass (subwoofer) and subsonic filter with infinitely adjustable separating frequencies
· Infinitely variable bass equalisation
· Adjustable input sensitivity
· Electronic protective circuit against short circuiting, DC offset and excess temperature
· Mute switch for suppressing switch-on crackle interference
· Low-level outputs (cinch jacks) for connecting additional amplifiers
· Capsulated and gilded loudspeaker and power-supply screw terminals
· Status indicator (green LED) and overload indicator (red LED)
· Remote control for volume control
3. IMPORTANT INSTALLATION INFORMATION
· This appliance may only be connected to a 12 volt system with negative ground.
· The heat radiated when the amplifier is used means that sufficient air circulation is required at the place of installation. It is very
important that the cooler's cooler ribs do not contact any metal plating or any surfaces which could impair air circulation. The
amplifier may not be installed in small confined spaces or spaces without air circulation (e.g. spare wheel recess or under the vehicle
carpeting). Installation in the boot is recommended.
· Install the amplifier in such a way that it is protected as far as possible against vibrations and dust and dirt.
· Make sure that the input/output cables are sufficiently distant from the power supply cables as otherwise interference may occur.
· Make sure that the fuse and operating elements are accessible after installation.
· The appliance's reliability and performance depend on the quality of installation. Preferably get an expert to install the system,
particularly if you want to install several loudspeakers or a complex multi-way system.
4. CONNECTIONS
4.1 POWER SUPPLY AND AUTOMATIC SWITCHING ON
Important notice: Before commencing the installation, disconnect the plus terminals from the car battery in order to prevent
short circuits.
The power cabling usually installed in on-board car networks is not sufficient for a power amplifier's demands. Make sure that the power
lines to GND and to the +12 V terminal have been sufficiently specified. A cable cross-section of at least 20 mm² must be used to connect
the battery to the amplifier's terminals.
First connect the amplifier's GND terminal to the battery's minus pole. It is very important that the connection is good. Dirt residues must
be carefully removed from the battery's connection point. A loose connection may cause malfunctions or interference noise or distortion.
The +12 V amplifier connection must then be connected with a power cable possessing an integrated fuse to the battery's plus pole. The
fuse must be located close to the battery, the length of cable from the battery's positive pole to the fuse must be less than 60 centimetres
for safety reasons. Only insert the fuse when all installation work, including the connection of the loudspeakers, has been completed.
Now connect the car hi-fi receiver's remote control connection to the amplifier's REM control jack. A cable with a cross-section of 0.75 mm²
is sufficient for connecting the amplifier's REMOTE connection and the control device.
1200 W on 4 ohm
350 W on 4 ohm
1500 W on 2 ohm
600 W on 2 ohm
2400 W on 1 Ohm
900 W on 1 Ohm
2 – 8 Ohm
5 – 150 Hz (-3 dB)
< 0.05 % (1 kHz)
> 100 dB
0.2 – 6 V
20 kOhm
40 – 300 Hz, 12 dB per octave
10 – 40 Hz, 12 dB per octave
0...10 dB at 45 Hz
+12 V (10 – 14.4 V), minus to ground
2 x 35 A
340 x 50 x 248 mm
3.5 kg
7