Herunterladen Diese Seite drucken

Philips GC2860/12 Bedienungsanleitung Seite 2

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 4
English
introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the
support that Philips offers, register your product at www.philips.com/welcome.
general description (Fig. 1)
A Spray nozzle
B Cap of filling opening
C Spray button 8
D Steam control
-
b= Calc-Clean function
-
0 = no steam
-
l = minimum steam
-
; = maximum steam
E
Steam boost button \
F
Auto-off light (GC2860 only)
g Mains cord
h Temperature light
i
Anti-Calc tablet (GC2860/GC2840/GC2830/GC2820 only)
Note: Anti-Calc tablet not visible from the outside.
J
Type plate
K Water tank
l
Temperature dial
M Soleplate
important
Read this user manual carefully before you use the appliance and save it for future
reference.
Danger
-
Never immerse the iron in water.
Warning
-
Check if the voltage indicated on the appliance corresponds to the local mains
voltage before you connect the appliance.
-
Do not use the appliance if the plug, the mains cord or the appliance itself shows
visible damage, or if the appliance has been dropped or leaks.
-
If the mains cord is damaged, you must have it replaced by Philips, a service
centre authorised by Philips or similarly qualified persons in order to avoid a
hazard.
-
Never leave the appliance unattended when it is connected to the mains.
-
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
-
Children should be supervised to ensure that they do not play with the
appliance.
-
Do not let the mains cord come into contact with the hot soleplate of the iron.
Caution
-
Only connect the appliance to an earthed wall socket.
-
Check the mains cord regularly for possible damage.
-
The soleplate of the iron can become extremely hot and may cause burns if
touched.
-
When you have finished ironing, when you clean the appliance, when you fill or
empty the water tank and also when you leave the iron even for a short while:
set the steam control to position O, put the iron on its heel and remove the
mains plug from the wall socket.
-
Always place and use the iron on a stable, level and horizontal surface.
-
Do not put perfume, vinegar, starch, descaling agents, ironing aids or other
chemicals in the water tank.
-
This appliance is intended for household use only.
Electromagnetic fields (EMF)
This Philips appliance complies with all standards regarding electromagnetic fields
(EMF). If handled properly and according to the instructions in this user manual, the
appliance is safe to use based on scientific evidence available today.
Before first use
1
Remove any sticker or protective foil from the soleplate.
2
Let the iron heat up to maximum temperature and pass the iron over a piece
of damp cloth for several minutes to remove any residues from the soleplate.
Preparing for use
Filling the water tank
Do not put perfume, vinegar, starch, descaling agents, ironing aids, chemically
descaled water or other chemicals in the water tank.
1
Switch off the appliance and unplug it.
2
Set the steam control to position 0 (= no steam) (Fig. 2).
3
Open the cap of the filling opening.
4
Tilt the iron and fill the water tank up to maximum level under the tap (Fig. 3).
Note: Do not fill the water tank beyond the MAX indication.
Note: If the tap water in your area is very hard, we advise you to use distilled water. Do
not use chemically descaled water.
All manuals and user guides at all-guides.com
-
If you do not know what kind or kinds of fabric an article is made of, determine the
right ironing temperature by ironing a part that will not be visible when you wear or
use the article.
Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent
shiny patches. Avoid using the spray function to prevent stains.
Note: Make sure that the steam setting you select is suitable for the set ironing
temperature.
,
,
Note: The iron may give off some smoke when you use it for the first time. This stops after
a short while.
-
-
Note: The iron starts to produce steam as soon as it has reached the set temperature.
You can use the spray function at any temperature to moisten the article to be
ironed. This helps remove stubborn creases.
A powerful boost of steam helps to remove very stubborn creases.
The steam boost function only works at temperature settings between 3 and
MAX.
You can also use the steam boost function when you hold the iron in vertical position.
This is useful for removing creases from hanging clothes, curtains etc.
Never direct the steam at people.
This iron is equipped with a drip-stop function: the iron automatically stops producing
steam when the temperature is too low to prevent water from dripping out of the
soleplate. When this happens you hear a click sound.
The automatic shut-off function automatically switches off the iron if it has not been
moved for a while.
5
Close the cap of the filling opening ('click').
selecting the temperature and the steam settings
Fabric type
Temperature setting
Linen
MAX
Cotton
3
Wool
2
Silk
1
Synthetic fabrics (e.g. Acrylic,
1
nylon, polyamide, polyester).
Check the laundry care label for the required ironing temperature:
1
To set the appropriate ironing temperature, turn the temperature dial to the
appropriate position (see 'Temperature and steam settings table') (Fig. 4).
2
Set the appropriate steam setting (see 'Temperature and steam settings table').
3
Put the iron on its heel.
4
Put the mains plug in an earthed wall socket.
The temperature light goes on.
5
When the temperature light goes out, wait a while before you start ironing.
During ironing, the temperature light goes on from time to time. This indicates
that the iron is heating up to the set temperature.
Using the appliance
steam ironing
1
Make sure that there is enough water in the water tank.
2
Set the recommended ironing temperature (see chapter 'Preparing for use',
'Temperature and steam setting table').
3
Set the appropriate steam setting. Make sure that the steam setting is suitable
for the ironing temperature selected:
$ for minimum steam (temperature settings 2 and 3).
& for maximum steam (temperature settings 3 to MAX).
ironing without steam
1
Set the steam control to position 0 (= no steam) (Fig. 2).
2
Set the recommended ironing temperature (see chapter 'Preparing for use',
'Temperature and steam setting table').
Features
spray function
1
Make sure that there is enough water in the water tank.
2
Press the spray button several times to moisten the article to be
ironed (Fig. 5).
steam boost function
1
Press and release the steam boost button (Fig. 6).
Vertical shot of steam
1
Hold the iron in vertical position and press and release the steam boost
button (Fig. 7).
Drip stop
Automatic shut-off function (specific types only)
Steam setting
Steam boost
&
Yes
Yes
&
N.A.
$
0
N.A.
0
N.A.

Werbung

loading

Diese Anleitung auch für:

Gc2800-serie