Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
OPERATING MANUAL FOR
ROPELIGHT
LED PENLIGHT PRO 230V
Read this short manual carefully and keep it accessible for further
reference!
SAFETY MESSAGES
Disregard of the safety messages may lead to danger of life, burning or
fire!
Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
The product may not be modified or converted.
Do not hang or fasten anything on the product, especially no decoration.
Do not cover the product - provide free air circulation.
The luminaire may only be operated with a complete and intact protection
glass.
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
This product is not intended to be used by children. Ensure that children do
not suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol:
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
only be installed according to safety class II (two).
only be operated when firmly mounted on a stable, even and tilt-fixed
surface.
only be operated on normally or not flammable surfaces.
not be exposed to strong mechanical loads or to strong contamination.
MAINTANANCE AND CARE
Light source
Under regular usage the LED light source has an extraordinary long lifetime. If
nevertheless damage or failure occurs, contact your local dealer to exchange
the LED light source.
Care
The following enviromental influences may have unwanted effects on the
surface of the product:
acid rain and sour soil, high salt content in the air
cleaning agents, fertilizer especially in flowerbeds
thawing salt, other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Disconnect the product from the power supply and let it cool down, before
you clean the product.
Clean the product on a regular basis using a slightly moistened, soft and fluff-
free cloth. Please also note additional supplied notes on maintanance and
care.
STORAGE AND DISPOSAL
Storage
The product must be stored in a dry and clean environment. Do not strain
the product mechanically during storage.
After a damp or soiling storage the product may only be installed after
checking its condition by an approved electrician.
Disposal (European Union)
Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive(WEEE,
2003/108) on electrical and electronic devices at local collection points for
such devices!
.
INSTALLATION
(only by an approved electrician)
Switch off the mains or respectively the connection lead before doing any
works!
Use only parts, which are supplied with the product or are described as
accessories!
Inspect the product for loose parts inside the housing. When there are loose
parts inside the housing and these are not explicitly described the product may
not be installed or operated.
Use the supplied fastening material only when it is suited for the installation
background. If this is not the case use only fastening material suiting the
installation background.
Unpacking
Carefully take the product out of the packaging removing any transport
safeguards.
Before disposal of the packaging material make sure that all components of
the product are removed.
Installation place
The product is solely suited for installation on the wall, ceiling and floor.
LED react sensitive on high temperatures! Before installation pay attention
to the expected temperature at the place of operation. This may not exceed
the allowed ambient temperature (ta=40°C) of the product.
The product may only be utilized according to IP44.
IP44: Protection against foreign objects > Ø 1,0mm - Protection against
splashing water from all directions.
Prepare the power supply lead according to valid rules for outdoor
installations.
Do not seal the product yourself, using additional silicon or another
sealant.
Before installation
Make sure the light chain is not damaged by sharp edges and the like
when installing it. Do not strain the product mechanically.
The minimum bending radius may not be lower than 30 mm.
Do not operate the product rolled-up or in its package. The product may be
destroyed by its self-generated heat.
Do not connect this ropelight to other ropelights.
Installation steps (read completely before installation)
The attachment of end caps (SLV-art.-no. 232691) and any connectors
(SLV-art.-no. 232641) must be carried out water-proof.
Cutting
Be sure to cut the LED PENLIGHT PRO 230V only at the designated
marks!
Wrongly cut pieces must be discarded for safety reasons.
Connecting two ends
Ensure a reliable electrical connection.
Push one sealing ring on each end.
Press the stepped, pointedly forthcoming contacts connector firmly into the
wire ends of the two tube ends.
Put both tube ends in one half shell of the connector housing (SLV-art.-no.
232641). Put the other half shelf on top of it and screw it firmly to the lower
half shell of the housing.
You may operate up to 40,5m LED PENLIGHT PRO 230V on one feed-in.
Connection to feed-in
The LED PENLIGHT PRO 230V is ready for connection, featuring a
sealed-in connector.
Installation
Use the fastening clips (SLV-art.-no. 232651, 232681) or the profile (SLV-
art.-no. 232661) for mounting on a surface.
Check if the product functions properly and is securely fixed!
art.-no. 232711/12 232741/42 © 02.09.2015 SLV GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0
Technical Details are subject to change.
Werbung
Inhaltsverzeichnis
