BOMANN DU 7601 G Bedienungsanleitung, Garantie Seite 19

• Determine the position of the cooker hood central-
ly above the cooking area in accordance with the
specified safety distances.
Totally 6x mounting holes with a diameter of approx.
8 mm are necessary for the wall mounting. Insert the
(Fig. 1). (Fig. 1). (Fig. 1). (Fig. 1).
supplied dowels
• First mark the holes required for fixing the hood
body in accordance with the supplied drilling tem-
plate. Check the markings with a water balance
and make the holes.
Turn in the upper screws 2x ST4*30mm for the
-
suspension of the hood body so far that they
project approx. 5 mm out of the wall.
• Fasten the bracket for the upper shaft termination
with the screws 2x ST4*40mm after determining
the extension length of the shaft cover.
• Before attaching the hood
- Fasten the glass screen with the screws
4x M4*20mm in the screw insert made of rub-
ber together with washers on the hood body.
- Affix the connecting piece with inserted non-
return valves from the top of the extraction
duct with the screws 2x ST4*8mm.
Insert the two non-return valves by lightly
bending them from above into the connecting
(Fig. 2a) (Fig. 2a) (Fig. 2a) (Fig. 2a)
piece .
For the exhaust hose: For the exhaust hose:
For the exhaust For the exhaust hose: hose:
hose (supplied) with an inner diameter of 150 mm
must be attached. Secure the hose with the cable tie.
• Hang up the hood. Check the secure hold and the
horizontal position. Tighten the lower screws 2x
ST4*30mm through the hood body to secure the
(Fig. 3) (Fig. 3) (Fig. 3) (Fig. 3)
hood .
For the exhaust hose: For the exhaust hose:
For the exhaust hose: For the exhaust hose:
the exhaust hose and connect it with the outlet open-
ing.
(Fig. 2) 2) 2) 2) (Fig.
(Fig. (Fig. :
Hereupon a flexible exhaust
Check the correct position of
• Fit the telescoping shaft unit. Pull up the inner
shaft and fix the shaft cover to the side of the
bracket using the self-tapping screws 2x
(Fig. 4) ) ) ) (Fig. 4
(Fig. 4 (Fig. 4
ST4*8mm
Installing the activated carbon Installing the activated carbon Installing the activated carbon Installing the activated carbon filter for recirculation
mode mode mode mode
• Remove the aluminum grease filter (see "Clean-
ing the aluminum grease filter).
• Place the carbon filter onto the intake of the ex-
haust air duct. Make sure that the fixing pins of
the carbon filter engage in the fastening slots of
the exhaust air duct. Put the filter in A A A A and press
firmly flat B B B B .
• Reinstall the aluminum grease filter.
Electrical connection Electrical connection Electrical connection Electrical connection
WARNING: WARNING:
WARNING: WARNING:
• The installation to the mains supply must conform
to the local standards and regulations.
• Improper connection may cause to an electric
shock shock shock shock!
• Do not modify the appliance plug. If the plug does
not fit properly to the outlet, let install a proper
outlet by an authorized specialist.
• The accessibility of the power plug must be en-
sured to disconnect the appliance from the power
supply in case of emergency.
• Ensure that your mains power corresponds with
the specifications of the appliance. The specifica-
tions are printed on the rating label.
• Connect the mains cable to a properly installed
and earthed wall outlet.
• If the plug after installation is not accessible, a
corresponding disconnect device must be availa-
ble to meet the relevant safety regulations.
19
.
filter for recirculation filter for recirculation filter for recirculation
electric electric electric