Starting Operation - Bosch GLI 18V-4000 C Professional Originalbetriebsanleitung

12 | English
Cordless worklight
Level 1
Level 2
Level 3
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation and
during storage
Recommended rechargeable
batteries
Recommended chargers
Button cell
Protection class
Data transfer
C)
Bluetooth®
D)
Signal range
Frequency range used
Output power
A) At maximum brightness incl. remaining operating time in
dimmed mode
B) Limited performance at temperatures < 0 °C
C) The mobile devices must be compatible with the Bluetooth® ver-
sion specified and support the Generic Access Profile (GAP).
D) The signal range may vary greatly depending on external condi-
tions, including the receiving device used. The Bluetooth® range
may be significantly weaker inside closed rooms and through
metallic barriers (e.g. walls, shelving units, cases, etc.).
The colour rendition of illuminated objects can be distorted.
System requirements
Mobile device (tablet, smart- Android, iOS
phone)
A) Minimum system requirements can be found in the app store for
your mobile device (e.g. Google Play or iTunes).
Assembly
Putting the button cell into operation
(see figure A)
The cordless worklight is fitted with a button cell so that it
can be detected by the mobile device even if no battery (8)
is inserted.
Remove the separating film between the button cell (12)
and the button cell contact when using the tool for the first
time.
To open the battery compartment cover (11), turn it anti-
clockwise with a screwdriver and then lift off the battery
compartment cover. Remove the film from the button cell
contact and close the battery compartment cover back up.
1 609 92A 7NL | (17.05.2022)
Battery Charging (Accessory)
GLI 18V-4000 C
lm 1000
u
lm 2000
lm 4000
Note: The battery is supplied partially charged. To ensure
°C 0 to +35
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
°C –20 to +50
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
GBA 18V...
ProCORE18V... by the "Electronic Cell Protection (ECP)". A protective circuit
switches the cordless worklight off when the battery is
GAL 18...
drained.
GAX 18...
u
GAL 36...
V 3
type CR 2032
/III
To remove the battery (8), press the release button (10)
and pull the battery out of the cordless worklight. Do not use
Bluetooth® 4.2
force to do this.
(Low Energy)
Follow the instructions on correct disposal.
m 15
MHz 2402–2480
Operation
mW < 2

Starting Operation

Inserting the battery (see figure A)
Push the charged battery pack (8) into the battery
holder (14) until it clicks into place.
Setting up
Place the cordless worklight on a stable, level surface. Make
sure it is secure.
The safety brackets (3) protect the light (1) from damage,
should the cordless worklight be accidentally knocked over.
A)
Fastening to the Tripod
You can use the tripod mount (9) to screw the cordless
worklight onto a tripod.
Attach the cordless worklight firmly to the tripod. Ensure the
cordless worklight cannot come loose and/or fall over.
Ensure that the tripod has a firm footing.
Switching on/off and adjusting the brightness
On/off switch
Press once
Press twice
Press three times
Press four times
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
cordless worklight.
Do not continue to press the On/Off switch after the
worklight has been automatically switched off. The
battery can be damaged. Ensure that the battery is
charged and that the worklight has cooled before switch-
ing on the worklight again.
Function
Switches on the cordless worklight,
dimmed (level 1)
Switches on the cordless worklight,
dimmed (level 2)
Switches on the cordless worklight,
full brightness (level 3)
Switches off the cordless worklight
Bosch Power Tools