Bosch GSC 2,8 Professional Originalbetriebsanleitung Seite 12

12 | English
(1) On/off switch
(2) Chip deflector
(3) Auxiliary handle
(4) Screw on auxiliary handle
(5) Auxiliary handle mount
(6) Set screw for upper cutter
(7) Striker
(8) Upper cutter
(9) Fastening screw for upper cutter
(10) Bottom cutter
(11) Set screw for bottom cutter
(12) Fastening screw for bottom cutter
(13) Setting gauge
Technical Data
Sheet metal shears
Article number
Rated power input
Power output
No-load stroke rate n
0
Stroke speed under load
Max. steel sheet cutting
A)
capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
A) Refers to steel sheets of up to 400 N/mm
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑8.
Typically, the A-weighted sound pressure level of the power
tool is 79 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑8:
2 2
a = 16 m/s , K = 1.5 m/s .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
1 609 92A 7MN | (27.04.2022)
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Fastening the auxiliary handle (see figure A)
Unscrew the screw (4) out of the auxiliary handle (3) until
the auxiliary handle fits into the auxiliary handle mount (5).
Slide the auxiliary handle (3) into the auxiliary handle
GSC 2,8
mount (5). Tighten the auxiliary handle by turning it clock-
0 601 506 1..
wise.
W 500
Operation
W 270
−1
min 2400
u
−1
min 1500
mm 2.8
Starting Operation
kg 2.7
u
/Ⅱ
2
Switching On and Off
To switch on the power tool, slide the on/off switch (1) for-
wards so that I appears on the switch.
To switch off the power tool, slide the on/off switch (1)
backwards so that 0 appears on the switch.
Working Advice
u
u
u
u
Products that are only sold in AUS and NZ: Use a resid-
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Pull the plug out of the socket before carrying out any
work on the power tool.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
This power tool is not suitable for bench-mounted use.
It must not be clamped into a vice or fastened to a work-
bench, for example.
Wear protective gloves during work. Make sure that
cut sheet parts are not bent towards your body. Sharp
burrs develop on cut sheets; these can cause injury.
When necessary and while wearing gloves, press bending
sheet parts away from your body.
Bosch Power Tools