EINHELL 34.111.23 Originalbetriebsanleitung Seite 18

5.3 Fitting the blade (Fig. 7)
Fit the larger opening of the blade (Item 6) onto
the blade mount (A) of the blade plate (Item 7)
and pull it outwards in the direction of the arrow
until the blade latches into place as shown in Fig.
20.
5.4 Height adjustment (Fig. 8)
Undo (A) the union nut until the grass trimmer
handle can be moved in and out freely. Now set
the required working height and secure the hand-
le in this position by tightening the union nut again
(B).
5.5 Fitting the additional handle (Fig. 9)
Fit the additional handle (Item 2) to the mount
provided, paying attention to the teeth. Then
secure the additional handle with the help of the
screw provided.
5.6 Adjusting the additional handle (Fig. 9)
Undo the fastening screw (Item 3) on the additi-
onal handle until it can be moved forwards and
backwards without any great resistance. Set the
required position and tighten the adjustment lock
again.
5.7 Fitting the edge guide (Fig. 10)
Pull the ends of the edge guide (Item 5) slightly
apart and insert the ends in the holes provided in
the motor housing.
5.8 Installing the battery (Fig. 11/12)
Press the side pushlock (E) buttons of the battery
pack as shown in Fig. 12 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 11, make sure that
the pushlock buttons latch in place! To remove the
battery pack, proceed in reverse order.
5.9 Charging the battery (Fig. 13)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(10) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (11) into the battery
charger (10).
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
Anl_GC_CT_18_24_Li_SPK13.indb 18
GB
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.10 Battery capacity indicator (Fig. 14)
Press the button for the battery capacity indicator
(Item F). The battery capacity indicator (Item H)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
- 18 -
20.05.2022 09:34:42