Yamaha PM5D Bedienungsanleitung Seite 342

MIDI-Datenformat
4.6.2 Effect module names
MODULE NAME
Freeze Play button "FRZPLAY_"
Freeze Record button "FRZREC__"
Nothing will happen if the Effect Type is different.
4.7 Level Meter Data – Parameter change –
4.7.1 Format (Parameter change)
Once a Level Meter Request is received to enable transmission, the specified
meter data will be transmitted at 50 msec intervals for a duration of ten seconds.
If you want meter data to be transmitted continuously, you must transmit a
Request at intervals of no longer than ten seconds.
Reception
This message is echoed if [Parameter change ECHO] is ON.
Transmission
Once transmission is enabled by a Request, the meter data specified in the
Address will be transmitted on the [Rx CH] channel at a specific interval for a
specific duration. (The transmission interval and the duration of transmission
will differ between models of device.)
Transmission is disabled when the power is cycled, or when PORT settings are
changed.
If [Parameter change ECHO] is ON, the message is transmitted without change.
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUP ID 00111110 3E
MODEL ID 00001111 0F
DATA 00100001 21
CATEGORY
DATA 0mmmmmmm mm
0mmmmmmm mm
0mmmmmmm mm
0ddddddd dd
0ddddddd dd
: :
EOX 11110111 F7
*1 Two types of meter data are provided; data that uses the decay value
of the DSP as-is, and data that is converted via a table according to
the number of segments in the meter display.
4.7.2 Format
Reception
This message is received if [Parameter change RX] is ON and [Rx CH] matches
the Device number included in the SUB STATUS. This message is echoed if
[Parameter change ECHO] is ON.
When this is received, the meter data specified in the Address is transmitted on
the [Rx CH] channel at a specific interval for a specific duration.
If this is received with an Address UL = 0x7F, transmission of all meter data will
stop (will be disabled) immediately.
Transmission
If [Parameter change ECHO] is ON, the message is transmitted without change.
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0011nnnn 3n
GROUP ID 00111110 3E
MODEL ID 00001111 0F
DATA 00100001 21
CATEGORY
DATA 0mmmmmmm mm
0mmmmmmm mm
0mmmmmmm mm
0ccccccc ch
0ccccccc cl
EOX 11110111 F7
342
PM5D/PM5D-RH Bedienungsanleitung
channel
0:Effect1 - 7:Effect8
0:Effect1 - 7:Effect8
System exclusive message
Manufacture's ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Digital mixer
PM5D
REMOTE LEVEL METER
ADDRESS UL (See 4.7.3)
ADDRESS LU
ADDRESS LL
Data1 H (See 4.7.5) *1
Data1 L
End of exclusive
(Parameter request)
System exclusive message
Manufacture's ID number (YAMAHA)
n=0-15 (Device number=MIDI Channel)
Digital mixer
PM5D
REMOTE LEVEL METER
ADDRESS UL (See 4.7.3)
ADDRESS LU
ADDRESS LL
Request Ch Total Number H
Request Ch Total Number L
End of exclusive
Referenzteil
4.8 Time Counter Data – Time Code –
4.8.1 Format (Parameter change)
When transmission is enabled by receiving a Remote Time Counter request,
Time Counter data is transmitted at 50 ms intervals for a duration of ten
seconds. If you want counter data to be transmitted continuously, you must
transmit a Request at intervals of no longer than ten seconds.
Reception
This message is echoed if [Parameter change ECHO] is ON.
Transmission
When transmission is enabled by a request, Time Counter data is transmitted
for a specific duration.
Transmission is disabled when the power is cycled, or when PORT settings are
changed.
If [Parameter change ECHO] is ON, the message is transmitted without change.
System exclusive message
STATUS 11110000 F0
Manufacture's ID number (YAMAHA)
ID No. 01000011 43
n=0-15 (Device number=MIDI Channel)
SUB STATUS 0001nnnn 1n
Digital mixer
GROUP ID 00111110 3E
PM5D
MODEL ID 00001111 0F
Time Counter TC
DATA 00101011 2b
CATEGORY
Hour
DATA 0ddddddd dd
Minute
0ddddddd dd
Second
0ddddddd dd
Frame
0ddddddd dd
End of exclusive
EOX 11110111 F7
4.8.2 Format
Reception
This message is received if [Parameter change RX] is ON and [Rx CH] matches
the Device number included in the SUB STATUS. This message is echoed if
[Parameter change ECHO] is ON.
When this message is received, Time Counter data is transmitted on the [Rx
CH] channel for a specific duration.
If a message is received with 0x7F as the second byte of the Address, data
transmission will be stopped (disabled) immediately.
Transmission
If [Parameter change ECHO] is ON, the message is transmitted without change.
System exclusive message
STATUS 11110000 F0
Manufacture's ID number (YAMAHA)
ID No. 01000011 43
n=0-15 (Device number=MIDI Channel)
SUB STATUS 0011nnnn 3n
Digital mixer
GROUP ID 00111110 3E
PM5D
MODEL ID 00001111 0F
Time Counter TC
DATA 00101011 2b
CATEGORY
0: Request transmission
DATA 0ddddddd dd
0x7F: Request stop transmission
End of exclusive
EOX 11110111 F7
(Parameter request)