HIKMICRO EXPLORER Serie Kurzanleitung Seite 35

MANUAL AND THE APPLICABLE LAW, THE LATTER
PREVAILS.
These clauses apply only to the products bearing the
corresponding mark or information.
FCC Information
Note: This product has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
product generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this product does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV
technician for help.
EU/UKCA Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European standards listed
under the Directive 2014/30/EU (EMCD), Directive
2014/35/EU (LVD), Directive 2011/65/EU (RoHS).
This product and - if applicable - the
supplied accessories too are marked with
"UKCA" and comply therefore with the
following directives: Electromagnetic
Compatibility Regulations 2016, Electrical Equipment
(Safety) Regulations 2016, the Restriction of the Use of
Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012.
Directive 2012/19/EU (WEEE Directive):
Products marked with this symbol cannot
be disposed of as unsorted municipal
waste in the European Union. For proper
recycling, return this product to your local
supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see:
www.recyclethis.info.
According to the Waste Electrical and Electronic
Equipment Regulations 2013: Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the United Kingdom. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-003 (B)/NMB-003(B)
standards requirements.
Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.
Laws and Regulations
Use of the product must be in strict compliance with
the local electrical safety regulations.
Power Supply
 The input voltage for the device should meet the
Limited Power Source (5 VDC, 2 A) according to the
IEC61010-1 standard. Please refer to actual products
and technical specifications for detailed information.
Transportation

Keep the device in original or similar packaging while
transporting it.
 Keep all wrappers after unpacking them for future
use. In case of any failure occurred, you need to return
the device to the factory with the original wrapper.
 Transportation without the original wrapper may
result in damage on the device and the company shall
not take any responsibilities.
 Do not drop the product or subject it to physical
shock. Keep the device away from magnetic
interference.
Maintenance
 If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.
 Wipe the device gently with a clean cloth and a small
quantity of ethanol, if necessary.
 If the equipment is used in a manner not specified by
the manufacturer, the protection provided by the
device may be impaired.

Clean the lens with soft and dry cloth or wiping
paper to avoid scratching it.
Using Environment

Make sure the running environment meets the
requirement of the device. The operating temperature
shall be -10 °C to 50 °C (14 °F to 122 °F), and the
operating humidity shall be 95% or less, no condensing.
 Place the device in a dry and well-ventilated
environment.
 DO NOT expose the device to high electromagnetic
radiation or dusty environments.
 DO NOT aim the lens at the sun or any other bright
light.
 When any laser equipment is in use, make sure that
the device lens is not exposed to the laser beam, or it
may burn out.
Emergency
If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power
cable, and contact the service center.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road, Xixing
Subdistrict, Binjiang District, Hangzhou, Zhejiang
310052, China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products
might be subject to export controls in various countries
or regions, including without limitation, the United
States, European Union, United Kingdom and/or other
member countries of the Wassenaar Arrangement.
Please consult your professional legal or compliance
expert or local government authorities for any
necessary export license requirements if you intend to
transfer, export, re-export the thermal series products
between different countries.
Informationen zur Einhaltung gesetzlicher
Vorschriften und zur Sicherheit
Lesen Sie alle Informationen und Anweisungen in
diesem Dokument sorgfältig, bevor Sie das Gerät in
Betrieb nehmen und bewahren Sie sie zum
Nachschlagen auf.
Weitere Informationen und Anleitungen finden Sie auf
unserer Website unter www.hikmicrotech.com.
Weitere Informationen finden Sie auch in anderen
Dokumenten (falls vorhanden), die dem Gerät
33
Deutsch