Walchem WCTW100 Serie Betriebsanleitung Seite 33

OUTPUTS
R1-R3
Outputs>On/Off (R1-R3)
Details Screen
Content varies with
output type
>>On/Off (R1-R3)>Settings
HOA Setting
Setpoint
>>Flow Timer (R1-R3)
HOA Setting
Feed Duration
Only if HVAC mode is enabled
>>
Bleed and Feed (R1-R3)
HOA Setting
Feed Time Limit
Only if HVAC mode is enabled
>>
Bleed and Feed (R1-R3)
HOA Setting
Feed Percentage
>>Percent Timer
(R1-R3)
HOA Setting
Sample Period
Only if HVAC mode is enabled
>>Biocide Timer
(R1-R3)
HOA Setting
Bleed
>>Alarm
(R1-R3)
HOA Setting
Alarm Mode
Outputs
On/Off (R1-R3)
Bleed (R2)
Additional Settings for On/OFF:
Deadband Min Relay Cycle
Duty Cycle Period Hand Time Limit
Duty Cycle Reset Time Total
Output Time Limit Input
Reset Output Timeout Direction
Interlock Channels Name
Activate with Channels Mode
Additional Settings for Flow Timer:
Accumulated Volume Hand Time Limit
Reset Timer Reset Time Total
Reset Output Timeout Flow Input
Interlock Channels Name
Activate with Channels Mode
Min Relay Cycle
Additional Settings for Bleed and Feed:
Output Time Limit Hand Time Limit
Reset Output Timeout Reset Time Total
Interlock Channels Bleed
Activate with Channels Name
Min Relay Cycle Mode
Additional Settings for Bleed then Feed:
Feed Time Limit Hand Time Limit
Reset Timer Reset Time Total
Reset Output Timeout Bleed
Interlock Channels Name
Activate with Channels Mode
Min Relay Cycle
Additional Settings for Percent Timer:
Feed Percentage Hand Time Limit
Interlock Channels Reset Time Total
Activate with Channels Name
Min Relay Cycle Mode
Additional Settings for Biocide Timer:
Event 1 (through 10) Bleed Lockout
Repetition Add Last Missed
Week Interlock Channels
Day Activate with Channels
Start Time Min Relay Cycle
Duration Hand Time Limit
Prebleed Time Reset Time Total
Prebleed To Name
Mode
Cond Input
Additional Settings for Alarm:
On Delay Time Hand Time Limit
Off Delay Time Reset Time Total
Output Name
Interlock Channels Mode
Activate with Channels
Min Relay Cycle
Off
CCond (S1)
Off
Temp (S2)
>>Time Prop
(R1-R3)
HOA Setting
Setpoint
Only if HVAC mode is enabled
>>Int Sampling
(R1-R3)
HOA Setting
Setpoint
>>Manual
(R1-R3)
HOA Setting
Interlock Channels
Only if model W120/power relay bd installed
>>Pulse Prop
(R1-R3)
HOA Setting
Setpoint
>>Dual Setpoint
(R1-R3)
HOA Setting
Setpoint
>>Probe Wash
(R1-R3)
HOA Setting
Input
Only if HVAC mode is disabled
>>Timer
(R1-R3)
HOA Setting
Add Last Missed
29
No Alarms (1)
0 µS/cm
74.7°F
Additional Settings for Time Prop:
Proportional Band Hand Time Limit
Sample Period Reset Time Total
Output Time Limit Input
Reset Output Timeout Direction
Interlock Channels Name
Activate with Channels Mode
Min Relay Cycle
Additional Settings for Int Sampling:
Proportional Band Interlock Channels
Deadband Activate with Channels
Sample Time
Min Relay Cycle
Hold Time
Hand Time Limit
Maximum Blowdown Reset Time Total
Wait Time Cond Input
Trap Sample Name
Output Time Limit Mode
Reset Output Timeout
Additional Settings for Manual:
Min Relay Cycle
Hand Time Limit
Reset Time Total
Name
Mode
Additional Settings for Pulse Prop:
Proportional Band Min Relay Cycle
Min Output Hand Time Limit
Max Output Reset Time Total
Max Rate Input
Output Time Limit Direction
Reset Output Timeout Name
Interlock Channels Mode
Activate with Channels
Additional Settings for Dual Setpoint:
Set Point 2 Min Relay Cycle
Deadband Hand Time Limit
Duty Cycle Period Reset Time Total
Duty Cycle Input
Output Time Limit Direction
Reset Output Timeout Name
Interlock Channels Mode
Activate with Channels
Additional Settings for Probe Wash:
Input 2 Interlock Channels
Event 1 (through 10) Activate with Channels
Repetition Min Relay Cycle
Week, Day Hand Time Limit
Events per Day Reset Time Total
Start Time Name
Duration Mode
Sensor Mode
Hold Time
Additional Settings for Timer:
Event 1 (through 10) Min Relay Cycle
Repetition Hand Time Limit
Week, Day Reset Time Total
Events per Day Name
Start Time Mode
Duration
Interlock Channels
Activate with Channels