Husqvarna PW 130 Bedienungsanweisung Seite 16

CAUTION:
a rotating water jet on sensitive surfaces, for
example painted surfaces on a vehicle. The
rotating water jet can cause damage to the
surface.
• To install a nozzle, hold the spray lance with one
hand and push in the nozzle until it locks in position.
(Fig. 27)
• To remove a nozzle, push in the tab on the spray
lance and pull out the nozzle from the spray lance.
(Fig. 28)
To adjust the pressure of the water jet
The nozzle with a straight water jet has adjustable
pressure.
• To increase the pressure of the water jet, turn the
nozzle clockwise. (Fig. 29)
• To decrease the pressure of the water jet, turn the
nozzle counterclockwise. (Fig. 30)
To operate the product
1. Connect the product to a water source. Refer to
connect the product to a water source on page 16 .
2. Bleed the system. Refer to
page 17 .
3. Start the product. Refer to
page 17 .
To connect the product to a water
source
The product can be used with water from the water
mains or water from an open water source, for example
a lake or a water barrel.
• To connect the product to the water mains, refer to
To connect the product to the water mains on page
16 .
• To connect the product to an open water source,
To connect the product to an open water
refer to
source on page 16 .
To connect the product to the water mains
1. Install the garden hose adapter and the water filter to
the water inlet on the product if they are not installed.
To install the garden hose adapter on page
Refer to
15 .
2. Connect the garden hose to the water mains. Use a
½ in. garden hose that is 10–25 m long. (Fig. 31)
CAUTION:
the water mains must not be more than 1
MPa (10 bar).
16
Do not use the nozzle with
To bleed the system on
To start the product on
The water pressure in
3. Open the valve on the water mains and make sure
that water can flow freely from the garden hose. (Fig.
32)
4. Close the valve on the water mains.
5. Connect the garden hose to the water inlet on the
product. (Fig. 33)
6. Connect the power plug to a power source.
7. Open the valve on the water mains.
8. Bleed the system before you operate the product.
Refer to To bleed the system on page 17 .
To connect the product to an open water
source
The product can be used with water from an open water
source, for example a lake or a water barrel. Use a ½ in.
suction hose (not included) that is maximum 3 m long.
(Fig. 34)
To
CAUTION:
the water source must not be more than
20°C.
CAUTION:
more than 0.5 m above the water source.
1. If the garden hose adapter is installed, remove it
from the water inlet on the product. (Fig. 35)
2. Install a suction hose (not included) to the water inlet
on the product. (Fig. 36)
3. Put the suction hose in the water source and make
sure that the filter is fully submerged.
4. Push in the button on the spray handle and pull out
the high-pressure hose from the spray handle. (Fig.
22)
5. Connect the power plug to a power source.
6. Turn the power switch to the on (I) position and let
the product operate for 2 minutes.
7. Turn the power switch to the off (0) position.
8. Hold the spray handle tightly with one hand and
push the high-pressure hose into the quick coupling
on the spray handle. (Fig. 21)
CAUTION:
The water temperature
in the water mains must not be more
than 40°C.
The water temperature in
The product must not be
CAUTION:
Do not remove the water
filter in the water inlet.
CAUTION:
Do not use a suction
hose without a filter.
1839 - 006 - 21.10.2022