BD Sensors DMK 456 Montageanleitung

DE EN
Montageanleitung /
Mounting instructions
Druckmessumformer für Schifffahrt und Offshore /
Pressure Transmitter for Shipbuilding and Offshore
DMK 456, DMK 457, DMK 458, DMP 457
DMP 457
www.bdsensors.com
Headquarters Eastern Europe
BD SENSORS GmbH BD SENSORS s.r.o.
BD-Sensors-Str. 1 Hradištská 817
D - 95199 Thierstein CZ - 687 08 Buchlovice
Germany Czech Republic
Tel.: +49 (0) 9235-9811-0 Tel.: +42 (0) 572-4110 11
Fax: +49 (0) 9235-9811-11 Fax: +42 (0) 572-4114 97
Russia China
BD SENSORS RUS BD SENSORS China Co, Ltd.
39a, Varshavskoe shosse Room B, 2nd Floor, Building 10, No
RU - Moscow 117105 1188 Lianhang Rd.
201112 Shanghai,
Russia China
Tel.: +7 (0) 95-380 1683 Tel.: +86 (0) 21-51600 190
Fax: +7 (0) 95-380 1681 Fax: +86 (0) 21-33600 613
Diese Montageanleitung stellt einen Auszug
aus der ausführlichen Betriebsanleitung dar.
Bitte laden Sie sich diese auf unserer Home-
page herunter, falls Sie nicht mit dem Produkt
vertraut sind.
These mounting instructions are an excerpt from the complete
operating manual. It may be downloaded from our homepage, if
you are not familiar with the device.
http://www.bdsensors.de
http://www.bdsensors.com
– Technische Änderungen vorbehalten –
– Technical modifications reserved –
Englisch
WARNING! In order to avoid hazards to operators and
damages to the device, the following instructions have to
be performed by qualified technical personnel.
WARNING! Adhere to the safety and operating instructions
stated in the operation manual. Effective regulations on oc-
cupational safety, accident prevention as well as national
installation standards and approved engineering tech-
niques must in addition be complied with.
Limitation of liability
If the instructions in the operating manual are not adhered
to or if the device is inappropriately used, modified or dam-
aged, liability is not assumed and warranty claims will be
excluded.
Intended use
Ensure that the medium is compatible with the media-
wetted parts and that the device is suitable for the applica-
tion without restrictions. The technical data listed in the cur-
rent data sheet is binding.
Product identification
nominal designation ordering
pressure
code number
range
signal supply connector pinout
Pin configuration
Electrical M12x1
ISO 4400
connections (4-pin)
supply 1 1
2 2
supply
shield ground pin 4
Electrical Kabelfarben
Field housing
connections (IEC 60757)
supply IN + wh (white)
IN - bn (brown)
supply
shield gnye (green-yellow)
Wiring diagram
supply +
p
V
S
supply –
I
For the electrical connection, a shielded and twisted
multicore cable has to be used.
Mounting
WARNING! Install the device only in depressurized and currentless state!
WARNING! Use a suitable seal, corresponding to the medium and the pressure input.
DO NOT USE ANY ADDITIONAL SEALING MATERIALS; LINKE YARN; HEMP OR TEFLON TAPE
(for connection acc. DIN 3852)!
Connection acc. to DIN 3852 Connection acc. to EN 837
G1/4": approx. 5 Nm
G1/2": approx. 10 Nm
G3/4": approx. 15 Nm
The indicated tightening torques must not be exceeded!
Take note that no inadmissibly high mechanical stress occurs at the pressure port, since this may cause a shifting of the
characteristic curve or to the demage. This is especially important for very small pressure ranges as well as for devices with a
pressure port made of plastic.
serial
For more information, please read the detailed operating manual!
Certificate
The pressure transmitters DMK 456,
DMK 457, DMK 458 and DMP 457
fulfil the requirements of DNV GL
(Det Norske Veritas Germanischen
Lloyd).
The certificate is available for down-
load on our homepage:
http://www.bdsensors.com
NPT connections
G1/4": approx. 20 Nm 1/4" NPT: approx. 30 Nm
G1/2": approx. 50 Nm 1/2" NPT: approx. 70 Nm
Flange connection
Fasten the flange with 4 resp. 8
screws (depending on flange
version) on the counter flange.
MA_DMU für Schifffahrt_180118