Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Specifications
Product
Article number
LED strip
LED strip length
Brightness
Light colour
LED type
LED quantity
Connection
Power
Waterproof
Controller
Input voltage
Max. current
Rated power
Frequency range
Max. transmit power
Waterproof
a
Quick start guide
Wi-Fi Smart COB LED strip
For more information see the extended manual online:
ned.is/wifilsc20crgb
Intended use
This product is a Smart Wi-Fi LED strip with a wireless remote control.
The product is not intended for professional use.
The product is intended for indoor use only.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Main parts (image A)
1
Power cable
Controller
2
3
Brightness buttons
4
Power button
Mode button
5
Controller plug
6
7
IR receiver
Safety instructions
-
WARNING
• Ensure you have fully read and understood the instructions in
this document before you install or use the product. Keep the
packaging and this document for future reference.
• Only use the product as described in this document.
• Do not use the product if a part is damaged or defective. Replace
a damaged or defective product immediately.
• Do not drop the product and avoid bumping.
• This product may only be serviced by a qualified technician for
maintenance to reduce the risk of electric shock.
• Do not expose the product to water or moisture.
• Do not switch on the LED strip if it is still coiled on the plastic reel.
Installing the app
1. Download the Nedis Smartlife app for Android or iOS on your
phone via Google Play or the Apple App Store.
2. Open the Nedis Smartlife app on your phone.
WIFILSC20CRGB
8
LED strip
Brightness buttons (remote)
9
q
Colour buttons
w
Previous mode button
Power button (remote)
e
White light button
r
t
Mode button (remote)
Wi-Fi Smart COB LED strip
WIFILSC20CRGB
2 m
860 lm
RGB + 2700K
COB
640 per meter
5 pins at 2.5 mm each
10 W
IP20
24 VDC
0.75 A
14 W
2412 - 2472 MHz
16 dBm
IP20
3. Create an account with your mobile phone number or your
e-mail address and tap Continue.
4. Enter the received verification code.
5. Create a password and tap Done.
6. Tap Add Home to create a SmartLife Home.
7. Set your location, choose the rooms you want to connect with
and tap Done.
Connecting the product
1. Plug the power cable A
2. Plug the controller plug A
3. Plug the power cable A
4. Check if the LED strip A
If the LED strip A
8
does not blink, press and hold the power
4
button A
on the controller A
4
5. Tap + in the top right corner.
6. Under Search Device, select the product from the list of available
devices.
Check if the LED strip A
4
7. Enter the password of the Wi-Fi network to which your phone is
connected and tap Confirm.
8. Rename the product after it has been found and added.
Setting up the product
1. Unplug the power cable A
2. Clean the surface from dust and grease.
The surface must be smooth. Do not place the product on
4
knitted/wool fabrics, dust wall, rough plastic surface or frosted
glass.
3. Remove part of the 3M tape from the back of the LED strip A
4. Place the start of the LED strip A
Make sure the power outlet is within reach.
4
5. Unroll the LED strip A
strip A
into the desired position.
8
6. Firmly press the LED strip A
-
Do not use hard objects to press the LED strip A
prevent damage.
-
Do not bend the LED strip A
damage.
If desired, cut the LED strip A
4
4
into the controller A
1
2
.
into the LED strip A
6
8
1
into a power outlet.
8
is blinking. If so, confirm in the app.
for 5 seconds.
2
8
is blinking. If so, confirm in the app.
1
from the power outlet.
in the desired position.
8
8
, remove the 3M tape and press the LED
8
down with your hand.
8
8
at sharp angles to prevent
8
to size on the indicated cut lines.
.
8
.
down to
Werbung
Inhaltsverzeichnis
