Adjusting The Depth Guide - Renovator Twist-A-Saw Deluxe Kit Bedienungsanleitung

Part: 2
Adjust the Comfort Control Grip to the desired position .
Part: 3
Tighten the Comfort Control Grip locking knob .
ADJUSTING THE DEPTH GUIDE (Fig . 5)
The cutting bit should always extend past the depth guide foot by
4mm (3/16")more than the thickness of the material being cut .
Example: If you were to cut 10mm (3/8") plasterboard, the
cutting bit should extend 14mm (9/16") past the bottom of
the depth guide foot, and therefore 4mm (3/16") through the
10mm (3/8") plasterboard .
Follow the steps below to adjust the depth guide .
Part: 1
Loosen the Depth Guide locking knob (1) . Slide the Depth
Guide foot (2) up or down to set the desired depth .
Part: 2
Tighten the Depth Guide locking knob securely .
Part: 3
Re-check the bit depth before cutting . Ensure both the bit
and the collet are securely fastened .
ATTACHING THE CIRCLE CUTTER (Fig . 6)
Follow the steps below to attach the Circle Cutter .
Part: 1
Fit the Multi-Purpose Handle . Refer to Attaching the Multi-
Purpose Handle.
Part: 2
Adjust the Depth Guide depth . Refer to Adjusting the Depth
Guide
Part: 3
Unscrew the internal mounting disc (1) from the external
mounting disc (2) .
Part: 4
Place the internal mounting disc into the Multi-Purpose
Handle foot (3) .
Note: Make sure the scallops of the internal mounting disc
are seated correctly in the scallops of the Multi-Purpose
Handle foot .
Part: 5
Place the circle cutting guide mounting hole (4) over the
treaded portion of the internal mounting disc insert .
Note: Make sure the pivot pin (5) is pointing downwards .
Part: 6
Attach the external mounting disc to the internal mounting
disc . Hand-tighten .
Note: Make sure the boss (6) of the external mounting disc
goes through and sits firmly in the mounting hole . Hand-
tighten only . Do not over-tighten .
Part: 7
37
TwistaSaw_Manual_150826_AN.indd 37
Loosen the pivot pin knob (7) . Slide the knob to set the circle
radius and re-tighten .
Part: 8
Insert appropriate cutting bit in the collet and tighten . Refer
to Installing cutting bits .
Note: To check the circle radius setting, measure from the
pivot pin to the outside of the bit .
ATTACHING THE FENCE GUIDE (Fig . 7)
Follow the steps below to attach the Fence Guide .
Part: 1
Loosen the adjustable Fence Guide locking knobs (1) . There
are two: one on each side of the Multi-Purpose Handle foot .
Part: 2
Slide the adjustable Fence Guide (2) into the Multi-Purpose
Handle foot .
Part: 3
Set the adjustable Fence Guide depth and tighten the locking
knobs .
INSTALLING THE VACUUM HOSE (Fig . 8)
Follow the steps below to install the Vacuum Hose
attachment .
Part: 1
Insert the Vacuum Hose (1) into the vacuum collar (2) .
Part: 2
Insert the nozzle of your vacuum cleaner into the Twist-A-
Saw™ vacuum hose dock (3) .
Note: If your vacuum cleaner nozzle does not match the
Twist-A-Saw™ vacuum hose dock, use a piece of irrigation
hose as an adapter .
ATTACHING THE TWIST-A-FLEX™ (Fig . 9)
Follow the steps below to attach the Twist-A-Flex™ Rotary
Tool Attachment .
Part: 1
Switch Twist-A-Saw™ OFF and unplug it from the power
source . Refer to Turning the Twist-A-Saw™ on and off.
Part: 2
Remove existing bit if one is already in Twist-A-Saw™ .
Part: 3
Ensure the Ø 6 .35mm (Ø 1/4") collet is in the spindle . Refer to
Changing the collets.
Part: 4
Insert the Twist-A-Flex™ rotary tool tail (1) into the collet (2) .
Part: 5
When the Twist-A-Flex™ rotary tool tail is correctly placed in
the collet, press in the spindle locking button (3) . Tighten the
collet nut (4) clockwise by hand as far as possible .
Part: 6
Using the Ø 16mm (Ø 5/8") collet wrench, securely tighten
the collet nut . DO NOT use excessive force when tightening .
26/08/15 12:26