HERKULES KPS210 Originalbetriebsanleitung Seite 33

• Subsequently check the position of the angle indi-
cator. If necessary, loosen the pointer (28) using a
Philips screwdriver, set to position 45° on the angle
scale (27) and re-tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (fig. 1/2/3/6)
The cross cut mitre saw can be used to make mitre
cuts of 0° - 45° in relation to the work face.
Important. For mitre cuts, the adjustable stop rail
(8a) must be fixed at the inner position.
• Open the set screw (8b) for the moveable stop rail
(8a) and push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (8a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (8a)
and the saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (13) in the 0° position.
• Loosen the locking screw (23) and use the handle
(3) to angle the machine head (4) to the left, until
the pointer (28) indicates the desired angle meas-
urement on the scale (27).
• Re-tighten the locking screw (23).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(fig. 1/2/3/6)
The cross cut mitre saw can be used to make mitre
cuts to the left of 0°- 45° in relation to the work face
and, at the same time, 0° - 45° to the left or 0° - 45° to
the right in relation to the stop rail (double mitre cut).
Attention! For mitre cuts (inclined saw head), the
moveable stop rail (8a) must be fixed in the outer
position.
• Open the set screw (8b) for the moveable stop rail
(8a) and push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (8a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (8a)
and the saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (13) by loosening the set
screw (7).
• Using the handle (3), set the rotary table (13) to the
desired angle.
• Retighten the set screw (7) in order to secure the
rotary table.
• Undo the locking screw (23).
• Use the handle (3) to tilt the machine head (4) to the
left until it coincides with the required angle value
(in this connection see also section 8.6).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Re-tighten the locking screw (23).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (fig. 3)
• The cutting depth can be infinitely adjusted using
the screw (24). To do this loosen the locknut (24a)
on the screw (24). Turn the screw (24) in or out to
set the required cutting depth. Then re-tighten the
locknut (24a) on the screw (24).
• Check the setting by completing a test cut.
8.9 Changing the saw blade (fig. 1/2/3/9/10)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
• Swing the machine head (4) upwards and secure
with the stop for cutting depth limiting (25).
• Fold the saw blade guard (5) upwards until the saw
blade guard (5) is above the flange screw (29).
• With one hand insert the Allen key (C) in the flange
screw (29).
• Hold the Allen key (C) and slowly close the saw
blade guard (5) until it touches the Allen key (C).
• Firmly press the saw shaft lock (32) and slowly ro-
tate the flange screw (29) in clockwise direction.
The saw shaft lock (32) engages after no more than
one rotation.
• Now, using a little more force, slacken the flange
screw (29) in the clockwise direction.
• Turn the flange screw (29) right out and remove the
outer flange (30).
• Take the blade (6) off the inner flange and pull out
downwards.
• Carefully clean the flange screw (29), outer flange
(30) and inner flange.
• Fit and fasten the new saw blade (6) in reverse or-
der.
• Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade (6)
must coincide with the direction of the arrow on the
housing.
• Before continuing your work make sure that all
safety devices are in good working condition.
• Important! Every time that you change the saw
blade (6), check to see that it spins freely in the ta-
ble insert (10) in both perpendicular and 45° angle
settings.
• Important! The work to change and align the saw
blade (6) must be carried out correctly.
8.10 Replacing laser batteries (fig. 11)
• Remove the laser battery cover (34). Remove the
2 batteries.
• Replace both batteries with the same or an equiva-
lent type. Make sure that they are inserted with the
same polarity as the used batteries.
• Close the battery cover.
GB | 33