Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
Push the power switch (2) from "O" to "I" to turn stapler
u
on.
Fully depress contact trip (4) against the work surface and
u
the green indicator (3) should light up.
Pull trigger (1) fastener will drive into work surface.
u
Note: Maintain downward pressure on work surface until the
fastener is driven into the work surface.
Release trigger.
u
Lift contact trip off work surface.
u
Repeat steps 1 through 4 for next application.
u
Note: The contact trip needs to be depressed followed by a
trigger pull for each fastener followed by a release of both the
contact trip and trigger after each fastener.
Correct hand position (Fig. D)
Warning! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Correct hand position requires one hand on the main handle.
Maintenance
Your BLACK+DECKER appliance has been designed
to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper care and regular cleaning.
Regularly clean the appliance using a damp cloth. Do not
u
use any abrasive or solvent-based cleaner. Never let any
liquid get inside the appliance and never immerse any part
of the appliance into liquid.
Accessories
Warning! Since accessories, other than those offered by
BLACK+DECKER, have not been tested with this product,
use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only BLACK+DECKER recommended
accessories should be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
TRA704T – 6mm Flat Wire Staple 10.6x 1.26mm
u
TRA705T – 8 mm Flat Wire Staple 10.6x 1.26mm
u
TRA706T – 10mm Flat Wire Staple 10.6x 1.26mm
u
TRA708T – 12mm Flat Wire Staple 10.6x 1.26mm
u
TRA709T – 14mm Flat Wire Staple 10.6x 1.26mm
u
SWK‑BN0625T – 15mm/5/8"/18ga brad nails J type
u
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
8
(Original instructions)
Please recycle electrical products and batteries according to
local provisions.
Further information is available at www.2helpU.com
Technical data
Voltage
V
DC
Staple size
mm
Brad nail size
mm
Weight
kg
Level of sound pressure according to EN 660745:
Emission Sound pressure level: (L
Measured Sound power level: (L
Vibration total values (triax vector sum) according to EN 60745:
Vibration level: (ah): 5.7 m/s2; K=1.5 m/s
Declaration of conformity
The Supply of Machinery (Safety)
Regulations 2008
BCN115 Crafting Stapler
Black & Decker declares that these products described under
"technical data" are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended),
EN60745‑1:2009+A11:2010 and EN60745‑2‑16:2010.
These products conform to the following UK Regulations:
Electromagnetic Compatibility Regulations, 2016,
S.I.2016/1091 (as amended).
The Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment Regulations 2012, S.I.
2012/3032 (as amended).
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the techni-
cal file and makes this declaration on behalf of
Black & Decker.
Black and Decker UK, 270 Bath Road, Slough
BCN115
: 77 dB(A); K=3 dB(A);
PA)
): 88 dB(A); K=3 dB(A);
WA
2
Ed Higgins
Director - Consumer Power Tools
Berkshire, SL1 4DX
United Kingdom
15/12/2021
3.6
6 - 14
15
0.9
Werbung
Inhaltsverzeichnis
