Black & Decker BCN115 Originalanweisungen Seite 5

b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e. Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
f. Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130 °C may cause explosion. NOTE: The
temperature „130 °C" can be replaced by the temperature
„265 °F".
g. Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
b. Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers.
Additional Safety Instructions for Cordless stapler
Always wear safety glasses.
u
Always wear ear protection.
u
Only use fasteners of the type specified in the manual.
u
Do not use any stands for mounting the tool to a
u
support.
Do not disassemble or block any parts of the fastener
u
driving tool such as the contact trip.
Prior to each operation check that the safety and
u
triggering mechanism is functioning properly and that
all nuts and bolts are tight.
Do not use the tool as a hammer.
u
Do not use the tool on a ladder.
u
Never point any operational fastener driving tool at
u
yourself or at any other person.
(Original instructions)
While working, hold the tool in such a way that no
u
injuries can be caused to the head or to the body in
the event of a possible recoil due to a disruption in
the energy supply or hard areas within the work piece.
Never actuate the fastener driving tool into free space.
u
In the work area, carry the tool at the workplace using
u
only one handle, and never with the trigger actuated.
Consider the conditions in the work area Fasteners
u
can penetrate thin work pieces or slip off corners and
edges of the work piece, and thus put people at risk.
Do not drive fasteners close to the edge of the work
u
piece.
Do not drive fasteners on top of other fasteners.
u
Always assume that the tool contains fasteners.
u
Careless handling of the nailer can result in unexpected
firing of fasteners and personal injury.
Do not point the tool towards yourself or anyone
u
nearby. Unexpected triggering will discharge the fastener
causing injury.
Do not actuate the tool unless it is placed firmly
u
against the workpiece. If the tool is not in contact, the
fastener may be deflected away from your target.
Disconnect the tool from the power source when the
u
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
Do not use this tool for fastening electrical cables.
u
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
Labels on Appliance
The following symbols, along with the date code, are shown
on the appliance:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Vibration
The vibration and/or noise emission level given in this
information sheet has been measured in accordance with
a standardised test given in EN60745 and may be used
to compare one tool with another. It may be used for a
preliminary assessment of exposure.
WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However
if the tool is used for different applications, with different
accessories or poorly maintained, the vibration and/or noise
emission may differ. This may significantly increase the
exposure level over the total working period.
ENGLISH
5